JetCat P1000-PRO Скачать руководство пользователя страница 52

Страница: 52 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

The RUN Menu

As soon as the ECU is switched on, the

Run

menu is displayed.

In the lower display line, the actual engine RPM is indicated.
In the upper display line, the following selections can be monitored. Use the

+ / -

buttons alone for selecting the

different parameters.

Value

Explanation

Temp.

Current EGT (

xhaust

emperature).

The units, °C or °F can be selected in the LIMITs menu.

OffCnd
SetRpm

Last Off command (reason for shut down). See table on page 28

State

Current engine state.

U-Pump

Current pump voltage.

Airspeed

Current Air speed (km/h) this readout is usual for function check of the speed sensor.

Note: This readout is only supported by connected airspeed sensor.

Set Speed

Target state-air speed (km/h). This readout is for checking at the “speed control” mode the set
target state-airspeed of throttle stick.
Note: This readout is only supported by connected airspeed sensor.

The Min/Max Menu

The Min/Max menu is used primarily for diagnostics purposes. All the following variables may be sampled manually by
pressing the

Change Value/Item

button on the GSU.

Value

Explanation

Upump-Max
Upump-Min

Maximum pump voltage.
Minimum pump voltage.

MaxTemp

MinTemp

Maximum EGT.

Minimum EGT.

MaxRpm
MinRpm

Maximum engine RPM.
Minimum engine RPM.

MaxAirSpd
AvgAirSpd

Maximum Airspeed (*)
Average Airspeed (*)

Flight Distance

Flight distance in km (*)

AvgRpm
MaxRTmp

Average-RPM
Average temperature at full throttle

AvgPump

AvgTemp

Average pump voltage

Average temperature

(*) Only by connected air speed sensor!

Содержание P1000-PRO







































































Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды

JetCat P1000-PRO, Руководство по эксплуатации

Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды