JetCat P1000-PRO Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 70

background image

M

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

6

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Power supply:

Typical via 3-cell LiPo battery / XT60 Power connector / capacity 3000mAh or higher
Max.(peak) electrical startup power: 300W

On newer engines, supply voltage can range from 10-35V max. On these systems the battery type and cell count is
adjustable in a large range. On these engines the output voltage of the integrated DC/DC converter will automatically
adjust in correspondence to the selected battery! (only GL/GH versions).

On older GL/GH engines the battery must be a 3s Lipo type, as the output voltage of the DC/DC converter is fixed and
matched to these battery voltages!

Data connector:

Via 15pin SUB-D (male) this provides for the following control options:



1x Power On control signal



2x PWM input channels (e.g. for RC remote control; THR/AUX)



2x independent serial interfaces (

baudrate:9600 up to 115000 bps)

for computer remote control, data

reporting and/or interconnection of multiple engines, RS485 signal level upon request.

Engine addressing feature allows to connect multiple engine to same serial interface.



1x analogue voltage control / sensor input



1x JetCat Bus interface, e.g. for connection of GSU and/or other JetCat accessories (LCU / flow sensor/ BMS
system etc.)



CAN-Bus interface for control and data reporting



Customer specific data connectors including customer specific pinouts are possible on request

JetCat PRO-Interface, Option

By using the “JetCat-PRO” interface, not only can all PRO engines easily be used in RC-model applications, it provides a

ready-made solution, and easy interface point for educational and industrial applications.
It also provides full functionality of our JetCat Telemetry-Adapter if desired!
Furthermore, the PRO-Interface allows for an easy access point to connect other accessories such as:



One or two channel RC control (from receiver)



Telemetry output for: Jeti, Graupner, Hott, Multiplex M-BUS and Futaba SBUS-2



RJ12 jack for connection of GSU



Air Speed sensor header



6 and 8 pin ERNI flat cable connectors (e.g. for connection of LCU / Mini GSU)



RS232 header for computer control



CAN-Bus header



Header to JetCat BMS (Battery Management System)



Cross check communication port (for interconnecting / synchronizing two engines).



3x Status LEDs



Analog and digital inputs for:

- Power On/Off
- Engine On/Off Control
- Engine RPM command/ control via a directly connected potentiometer

«
...
4
5
6
7
8
...
»

Содержание P1000-PRO







































































Отзывы:

Нет отзывов

Похожие инструкции для P1000-PRO

Бренд: Stobag Страницы: 40

Бренд: DIMOEL Страницы: 8

Бренд: MTHTrains Страницы: 20

Бренд: Lycoming Страницы: 83

Бренд: Volvo Penta Страницы: 64

Бренд: Volvo Penta Страницы: 104

Бренд: ARRI Страницы: 28

Бренд: YS Страницы: 2

Бренд: Yanmar Страницы: 394

Бренд: Baumuller Страницы: 22

Бренд: WilTec Страницы: 30

Ultra Drive UN-99

Бренд: Bettcher Страницы: 29

Бренд: KRESS Страницы: 16

Бренд: DLE Страницы: 24

Бренд: Torini Страницы: 16

Бренд: HPI Racing Страницы: 16

Бренд: FAAC Страницы: 20

Бренд: Toyota Страницы: 259

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды