JetCat P1000-PRO Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 70

background image

M

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

4

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

T

HE

INFO

M

ENU

........................................................................................................................................................... 54

T

HE

S

TATISTIC

-M

ENU

................................................................................................................................................... 55

T

HE

LIMIT

S

M

ENU

....................................................................................................................................................... 56

SPECIAL FUNCTIONS ................................................................................................................................................. 64

T

EMPERATURE CALIBRATION

......................................................................................................................................... 64

R

ESET TO

D

EFAULT

V

ALUES

.......................................................................................................................................... 65

FIRMWARE UPDATE ................................................................................................................................................... 66

JETCAT THREE YEAR LIMITED WARRANTY. .................................................................................................... 69

Introduction

Welcome to the Jet Age of model aircraft!

JetCat

is pleased to sell, support and service the

JetCat

engine and greatly

appreciates your purchase. We hope the

JetCat engine

brings you many days of pleasurable flying.

To begin, read this manual thoroughly. Develop an overall impression of the engine and its operating procedures,
equipment, and accessories. Study the material step-by-step and ascertain how to install, operate, and maintain your

jet engine. If you are unsure about anything, re-read it again, or contact JetCat for further support.

DO NOT OPERATE THE

JetCat ENGINE

BEFORE YOU HAVE READ THE MANUAL AND FULLY UNDERSTAND EVERY

PROCEDURAL DETAIL

Should you still have doubts or questions, do not hesitate to contact

JetCat

for further assistance.

The

JetCat

jet engine closely functions like a full-size jet engine. A centrifugal compressor compresses the incoming air

which is mixed in the combustion chamber with fuel (jet fuel / kerosene) and ignited. The result is a rapidly expanding
volume of gas that drives an axial engine wheel. The gas exiting the exhaust cone produces the required thrust for the
jet model. To start the engine, an electric motor is mounted on the front of the engine.

«
...
2
3
4
5
6
...
»

Содержание P1000-PRO







































































Отзывы:

Нет отзывов

Похожие инструкции для P1000-PRO

VLT AutomationDrive FC 300 Series

Бренд: Danfoss Страницы: 56

Бренд: Danfoss Страницы: 2

Бренд: Eurotronic Страницы: 4

Бренд: Kohler Страницы: 109

Бренд: Waterworld Страницы: 30

Бренд: MTU Страницы: 163

Бренд: Teryair Страницы: 13

Бренд: Siemens Страницы: 50

Worm Gearbox S 5 BA 2012

Бренд: Siemens Страницы: 54

SINAMICS S120 1PM4

Бренд: Siemens Страницы: 100

SIMOTICS-T 1FW6 Series

Бренд: Siemens Страницы: 106

SIMOTICS XP 1MD4

Бренд: Siemens Страницы: 128

SIMOTICS TN 1LL8

Бренд: Siemens Страницы: 148

SIMOTICS XP 1MB155

Бренд: Siemens Страницы: 152

SIMOTICS XP 1MB5 SH400

Бренд: Siemens Страницы: 166

Бренд: Siemens Страницы: 170

SIMOTICS XP 1LA5

Бренд: Siemens Страницы: 174

SIMOTICS-T 1FW68

Бренд: Siemens Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды