JetCat P1000-PRO Скачать руководство пользователя страница 59

Страница: 59 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

BATT or FUEL LOW:

The valve will pulse in any of these conditions

FAIL- SAVE

: The valve will pulse if the ECU detect a fail safe

BATT,FUEL,FAILS:

The valve will pulse in any of these conditions

ENABLESmokePmp:

Enables signal for smoke pump only if engine is running.

The pump can’t run without a running engine
(only useful by operate a JetCat Smoke pump)

High-Temp.

The valve will be pulse in case of excessive exhaust

temperature.

MaxRPM-reached:

The valve will be pulsed if the engine has reached its

maximum RPM.

Disabled:

No function, off.

Note:

The smoke warn function is switched off while the throttle stick is in idle position.

Operation mode

See page: 28, Operation modes

THR-Ctrl Input

The following options are available:

ServoPWM direct

: Engine control via Servo PWM Signal

AirSpeed Signal

: Engine control via analogue Signal on “AirSpeed” input

IdleThrResponse

Adjustment of the throttle response (acceleration) by idle (up to average speed)

Fast

default setting

Normal

average acceleration

Slow

slow acceleration for excessive warm weather or for operate

more than 1000m sea level

FullThr Response

Adjustment of the throttle response by full throttle (from average speed to full)

Fast

default setting

Normal

normal acceleration (for operation above 1000m)

AutoRestart

In case the engine would flame out during normal run, the system can be programmed
to automatically try a restart of the engine and resume operation. Per default the Auto
restart feature is disabled for safety reasons.

A restart always can be interrupted via the normal controls which stop the engine.

The following options are selectable:

Disabled

(Default, recommended)

Enabled

(engine will be restarted in case of flame out)

ThrottleMax

(engine will be restarted instantly, but operator must bring throttle stick to

full throttle position within 6 seconds (after the flameout happened) in order not to
interrupt/stop the restart attempt.

AirSpeed units

Displayed flight speed unit in

km/h

mph

Содержание P1000-PRO







































































Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды

JetCat P1000-PRO, Руководство по эксплуатации

Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды