JetCat P1000-PRO Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 70

background image

M

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

61

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

ThrustDiffOffDly

Allowed time in multiples of 0,1s where the thrust differential compared to other engine
in Newtons is allowed to be higher than the programmed window. A setting of 0 disables
the shut down due too high differential thrust, the limiter function stays active though.
Only available if “Engine CrossChk” is not set to “Disabled”

Generator-Charge

Generator function Enabled or Disabled; only on engines with generator functionality

StartUp Mode

This function allows to select different start procedures for the THR-input (PWM or
analogue signal)

You can select between following settings:

[SEQUENCE]:

Default setting: Throttle trim to maximum, throttle stick to idle, AUX switch to center
and now move the throttle stick to maximum to start the engine.

By using the Single Channel Mode (devoid of the AUX switch) start the engine by set the
throttle trim to maximum and then move the throttle stick to maximum.

THROTTLE MAX:

Throttle trim and throttle stick to maximum. Turbine starts if the AUX-switch is set to
center.

By Single Channel Mode (devoid of AUX switch) the engine starts by move the throttle
stick more than 95% of maximum.

THROTTLE MIN:

Throttle trim to maximum and throttle stick to minimum. Turbine starts if the AUX-
switch is set to center.

By Single Channel Mode (devoid of AUX switch) the engine starts by move the throttle
stick more than 95% of maximum.

IMMEDIATE:

The engine starts direct by move the throttle trim to maximum and set the AUX-switch
to center.
By Single Channel Mode only move the throttle trim to maximum for start.

Suggestions to start a multi-engine model

Two channel Mode:

Program one ECU to

THROTTLE MAX

mode but the second to

SEQUENCE

mode.

The “Throttle max engine” starts by move the throttle trim and throttle stick to
maximum and set the Aux switch to center. To start the “Sequence engine” you now
must move the throttle stick first to minimum and back to maximum.

Single channel mode:

Program one engine to

IMMEDIATE

mode, the other to

SEQUENCE

mode.

Throttle trim and throttle stick must be set to minimum. To start the “immediate engine”
just move the throttle trim to maximum. The “sequence engine” starts by move the

throttle stick to maximum.

«
...
59
60
61
62
63
...
»

Содержание P1000-PRO







































































Отзывы:

Нет отзывов

Похожие инструкции для P1000-PRO

Бренд: HunterDouglas Страницы: 20

Бренд: Grundfos Страницы: 25

Бренд: Daewoo Страницы: 199

MaxxForce 3.2H Euro V

Бренд: Navistar Страницы: 116

Бренд: Motorola Страницы: 82

Бренд: Petter Страницы: 58

Бренд: Texas Equipment Страницы: 38

GX 610 standard

Бренд: Honda Страницы: 69

Бренд: Wood-mizer Страницы: 80

120000 Intek I/C 850 Series

Бренд: Briggs & Stratton Страницы: 28

1941 4-cylinder engine

Бренд: Ford Страницы: 25

Бренд: Marine Power Solutions Страницы: 23

Бренд: Marine Power Solutions Страницы: 23

Бренд: HAMPTON BAY Страницы: 17

Бренд: Kärcher Страницы: 137

Бренд: JC ENGINE POWER Страницы: 8

Бренд: Franklin Страницы: 8

Бренд: Franklin Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды