JetCat P1000-PRO Скачать руководство пользователя страница 35

Страница: 35 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Now the ECU can memorize the positions of the throttle and AUX channels. First, place the throttle stick
and throttle trim to minimum. Next, press

Select Menu

or the LED I/O board button switch again. This will

store the R/C system’s pulse width for immediate shutdown of the engine. The green

LED will turn off

and the red

Pump running

LED will illuminate.

The GSU screen will display:



Throttle channel “

Idle

” position

Advance the throttle trim lever to maximum. Press

Select Menu

or the LED I/O board button switch again

to store the R/C system’s pulse width for the engine idle position. The red

Pump running

LED will turn off

and the yellow

Standby

LED will illuminate.

The GSU screen will display:



Throttle channel “

Full Power

” position

Advance the throttle stick to maximum. Press

Select Menu

or the LED I/O board button switch again to

store the R/C system’s pulse width for the engine full power position. The yellow

Standby

LED will turn off.

If your ECU is set up for single channel operation skip to instruction number

The GSU screen will display:



AUX channel minimum “

Off

” position.

If the ECU is set for two channel operation, continue to program the auxiliary channel. The green

LED

will illuminate again and initiates the learn mode for the three-position auxiliary channel.

Move the auxiliary channel to the minimum position for

Off

and press

Select Menu

or the LED I/O board

button switch again to store the R/C system’s pulse width for immediate shutdown of the engine. The
green

LED will turn off and the red

Pump running

LED will illuminate.

The GSU screen will display:



AUX channel center “

Start/Standby

”

position

Содержание P1000-PRO







































































Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды

JetCat P1000-PRO, Руководство по эксплуатации

Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды