JetCat P1000-PRO Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 70

background image

M

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

57

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

AUX-channel func

The AUX-channel (3-step switch) can be used for optionally special features or disabled
even for single-channel operation.

ON,TrbCtrl ON

:

Aux channel enabled for engine control

ON.TrbCtrl OFF

:

Aux channel enabled for additional functions like speed limiter functions, Smoker
control etc.
Turbine control disabled. The Aux channel is used only for additional control
functions. The engine control is only via the throttle channel ( Single Channel Mode)

NOT USED

:

Single Channel Mode.
Totally disabled AUX channel input for engine control, speed sensor and smoker
functions. AUX channel wire must not be connected to the receiver in this mode. In
case of a connected air-speed sensor the Maximum Limit Speed is still active and
limits the maximum speed of the plane. This safety function can’t be disabled.

AUX-SW0 Action

Only if the parameter “AUX-channel func” (see above) has been set to “ON, TrbCtrl OFF”
this option is visible. In this case, the AUX-channel (3-step switch) can be used for
optional controls or can be disabled.
This option defines the action taken if the 3-step switch is be set to the “SW0” position
(backwards position)

DISABLED/NONE

No Action

LowIdle active

Idle rpm will be reduced to the value set by the “LowIdleRpm” parameter

Turbine-OFF

The following options are only present with an airspeed sensor connected:

LrnSpeed Lo/Hi

LrnSpeed Lo
LrnSpeed Hi
Hold-Speed

AUX-SW2 Action

Only if the parameter “AUX-channel func” has been set to “ON, TrbCtrl OFF” this option

is visible. In this case, the AUX-channel (3-step switch) can be used for optional special
controls or be disabled.
This option defines the action taken if the 3-step switch is be set to the “SW2” position
(forward position)

DISABLED/NONE

No Action

LowIdle active

Idle rpm will be reduced to the value set with the “LowIdleRpm” parameter

The following options are only present with an airspeed sensor connected:

«
...
55
56
57
58
59
...
»

Содержание P1000-PRO







































































Отзывы:

Нет отзывов

Похожие инструкции для P1000-PRO

Бренд: Briggs & Stratton Страницы: 102

Бренд: Eurotronic Страницы: 4

MAESTRIA+ 50 io

Бренд: SOMFY Страницы: 112

Air Cooled TR-10D

Бренд: Wisconsin Страницы: 46

Бренд: Briggs & Stratton Страницы: 6

Бренд: KTM Страницы: 92

Бренд: STG-BEIKIRCH Страницы: 25

Бренд: Coleman Страницы: 79

Бренд: Honda Страницы: 12

Бренд: Honda Страницы: 57

Бренд: Alutech Страницы: 32

Бренд: Honda Страницы: 42

Бренд: Bticino Страницы: 4

Бренд: Honda Страницы: 28

Бренд: JAC Страницы: 801

Бренд: LIMBACH Страницы: 3

Бренд: Mitsubishi Страницы: 3

Бренд: GAPOSA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды