JetCat P1000-PRO Скачать руководство пользователя страница 26

Страница: 26 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

GSU Control Panel Descriptions

OPTIONAL: Mini GSU, Part# 61161-00

With all the functionality of the larger version
and, because of its small size and weight, it can
be mounted in the model providing direct access
to all information and functions.

Spool

– Runs starter motor for testing

or together with “Set” key to direct

start/stop engine from GSU

Starter -

LED, (yellow)

Ignition -

LED, (red)

Pump running -

LED, (red)

OK -

LED, (green)

Change value

key for altering engine

parameters in conjunction with the

◄

- or

►

keys

(4) Hotkeys

Directly enters the menu named on

the corresponding blue key

SET

– Enter parameters for several

functions or together with “Set” key

to direct start/stop engine from GSU

Alphanumeric, 2 line by 16 characters,

backlit LCD display

◄

- or

►

Scroll within a menu or through
different menus. Also used for

changing parameter values

Select Menu

key for selecting

different menus in conjunction with

the -

◄

- or

►

keys

Содержание P1000-PRO







































































Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды

JetCat P1000-PRO, Руководство по эксплуатации

Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды