JetCat P1000-PRO Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 70

background image

M

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

21

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

RC-Servo PWM inputs / Telemetry output /Airspeed input

The engine can be controlled by 1-2 Servo PWM inputs. If Servo PWM control is desired, at least the THR channel
needs to be connected.

Power on via RC-signal

Besides the control function, the positive supply voltage on the servo inputs (THR/AUX) is used to power up the
ECU/engine!
This means the ECU/engine will switched on as soon as the receiver is powered up / or when a voltage on the “+” pin
of the servo inputs is supplied to the PRO-Interface.

S + - (AUX)

AUX (auxiliary servo PWM
input channel)
Can be used for engine
ON/OFF control or for

controlling of a smoke pump
the airspeed sensor or other
features.

THR (throttle channel)

Signal (Servo PWM)
+
-

Input for airspeed

sensor (option)

Airspeed-Signal
+
-

Telemetry output

Telemetry-Signal

+

-

«
...
19
20
21
22
23
...
»

Содержание P1000-PRO







































































Отзывы:

Нет отзывов

Похожие инструкции для P1000-PRO

Бренд: Sumoto Страницы: 20

Бренд: Man Страницы: 64

Бренд: Vetus Страницы: 28

Бренд: BMW Страницы: 41

Бренд: YS Страницы: 2

TWINMOT T2-PLUS H

Бренд: Germany Motions Страницы: 12

Бренд: Yanmar Страницы: 76

Бренд: Yanmar Страницы: 234

Бренд: Briggs & Stratton Страницы: 13

Бренд: DAF Страницы: 40

Бренд: YARDMAX Страницы: 25

Бренд: Yanmar Страницы: 394

Бренд: WÄRTSILÄ Страницы: 196

Bell & Gossett Ecocirc XL

Бренд: Xylem Страницы: 52

Бренд: Man Страницы: 134

Бренд: Saito Страницы: 7

Бренд: Nanni Страницы: 93

Бренд: Nanni Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды