JetCat P1000-PRO Скачать руководство пользователя страница 39

Страница: 39 / 70

Ingenieurbüro CAT, M. Zipperer GmbH +49-7634-5056-800
Wettelbrunner Straße 6

[email protected]

79282 Ballrechten-Dottingen

www.jetcat.de

GERMANY

Instruction manual JetCat-PRO engines, 1.7 - V12.01V

Control via serial Bus (COM1)

Please refer to our separate available documentation on the serial control interface.

Control via CAN-Bus

Please refer to our separate available documentation on the CAN-bus protocol.

Preparing fuel and fuel system

Warning!

Obey local laws for the transportation and storage of fuels.

Fire warning!

When mixing the fuel with oil or when operating (fueling, defueling, etc.), never handle near an
open flame.

Please do not spill or empty fuel to the ground.

The

JetCat

engine can use deodorized kerosene, 1-K kerosene or Jet-A1 for fuel. Fuel must be mixed with 3-5%

synthetic engine oil.

Example formula:

1 quart of oil in 5 gallons of fuel.

JetCat

recommends low toxicity

JetCat

oil with anti-static additive or Aeroshell 500 engine oil although any engine oil

that conforms to MS23699 standards will work.

To reduce static charges from the fuel system, we recommend adding our anti-static additive (Part# 61198-00) or

JetCat

Turbine Oil (Part# 61197-00) with anti-static additive already blended in.

Please note:

Fully synthetic

2-stroke oils or Mobil DTE

are not suitable and must not be used.

Содержание P1000-PRO







































































Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды

JetCat P1000-PRO, Руководство по эксплуатации

Результаты поиска

Содержание P1000-PRO

Отзывы:

Похожие инструкции для P1000-PRO

Бренды по названию

Популярные бренды