IDT 89HPES16NT2 Скачать руководство пользователя страница 205 | Manualshive

Страница: 205 / 292

background image

IDT Non-Transparent Mode Operation

PES16NT2 User Manual

10 - 75

April 15, 2008

Notes

PCIE_NTBSTS - Non-Transparent Bridge Status (0x079)

2

OSCFGPROT

RW

0x0

1

Opposite Side Configuration Protection.

When this bit is

set, all configuration and BAR4 writes from the opposite
side of the non-transparent bridge to the internal or exter-
nal non-transparent bridge configuration capability struc-
ture are ignored (i.e., they are completed normally but do
not modify any values). Reads to this space via configura-
tion or BAR4 accesses when this bit is set return a value of
zero for all registers in the non-transparent bridge configu-
ration capability structure except for the NTBCFGC regis-
ter, which returns its actual value.

3

RAEN

RW

0x0

1

Reset Action Enable.

When set, this bit enables the side

effect specified by the Reset Action (RA) field in this regis-
ter when a fundamental or hot reset is detected on the
opposite side of the non-transparent bridge.
This field is only relevant for the internal side of the non-
transparent bridge and is read-only 0x0 in the external side
of the non-transparent bridge.

4

RA

RW

0x0

1

Reset Action.

This field specifies the action to be taken

when the RAEN bit is set in this register and a fundament
or hot reset is detected on the opposite side of the non-
transparent bridge.
This field is only relevant for the internal side of the non-
transparent bridge and is read-only 0x0 in the external side
of the non-transparent bridge.
0x0 -(thissidenotready) this side not ready. This causes the

OSMODE field in the NTBCTL register on the oppo-
site side of the non-transparent bridge to be set to not
ready.

0x1 -(oppositesidenotready) opposite side not ready. This

causes the OSMODE field in this register to be set to
not ready.

5

PEFR

RW

0x0

1

Propagate External Fundamental Reset.

When this bit is

set and the device is configured to operate in non-transpar-
ent mode, then assertion of the PENTBRSTN signal results
in a fundamental reset of the entire device.

6

Reserved

RO

0x0

Reserved field.

7

RST

RW

0x0

Fundamental Reset.

Writing a one to this bit initiates a

fundamental reset to the entire device. Writing a zero has
no effect. This field always returns a value of zero when
read.

1.

Not reset by external fundamental reset or internal/external hot reset

Bit

Field

Field

Name

Type

Default

Value

Description

0

OSFRD

RW1C

depends
on reset

condition

1

Opposite Side Fundamental Reset Detected.

This bit is

set when a fundamental reset is detected on the opposite
side of the non-transparent bridge.

Bit

Field

Field

Name

Type

Default

Value

Description

«
...
203
204
205
206
207
...
»

Содержание 89HPES16NT2





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 89HPES16NT2

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

ShareCenter DNS-343

Бренд: D-Link Страницы: 12

AirPlus G DWL-G710

Бренд: D-Link Страницы: 5

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

Бренд: D-Linke Страницы: 32

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: A-Link Страницы: 6

Бренд: LAWO Страницы: 154

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP Страницы: 14

Бренд: National Instruments Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды