manualshive.com logo in svg

ICT Hybrid Ultra ICT-2U4-DC12, Инструкция по эксплуатации, Страница: 68 / 97

Поделиться
Скачать
ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 68

Hybrid Ultra

 

 

855-350-050_Rev2.0_Instruction Manual 

                                               Page 

56

 of 84 

 

The  graphic  will  display  green  for  an  installed  LDM  that  is  working  as 
expected; a red display for an installed module that has an active alarm; and 
will be grey when a module is not installed in that slot. 
 

4.6.1

 

STATUS 

This tab shows the operating status and current loads of the circuit-breaker 
controlled outputs on the LDM module.  
 
If there is more than one LDM installed, they will show individually. 
 

Module Status 

Shows the slot that the LDM is installed in and the status (Alarm or OK).  
 

Module #x: Load Distribution 

 

 

 

Output #x

: Shows name and status of the output.  Will show amps being 

drawn. Will show OPEN if the breaker is turned off or has tripped due to 
an overcurrent event.  Will show OFF if the output is disabled in the GUI. 

 

Alarm Status

: Shows status of the LDM (Alarm or OK). 

 

4.6.2

 

SETTINGS & CONTOL 

This tab is used to adjust the setting on the LDM.  There will be a separate 
tab for each LDM that is installed in the unit. 
 

 

Содержание Hybrid Ultra ICT-2U4-DC12


































































































Отзывы:

Нет отзывов