ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 97

ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 15

Hybrid Ultra

855-350-050_Rev2.0_Instruction Manual

Page

3

of 84

1.1.5

Load Distribution Module (LDM)

•

TCP/IP remote management and power control of individual
outputs (with ICM installed)

•

Four fully managed load outputs with individual power cycling for
each output

•

Adjustable alarm and load-shed settings for each output

•

Monitoring and alarm reporting of each output

1.1.6

Power Chassis

•

Up to 7,500 watts of power with redundancy

•

Flexible configurations allow the DC power system to be matched
to the requirement

2.0

INSTALLATION

The following is the recommended sequence for the installation process.

2.1

Unpacking and Inspection

Perform a physical check of the unit as it is being taken out of the box to
ensure it has not been damaged during shipping. Check that the system
configuration matches the version ordered, and that the accessories under
the package contents section were shipped with the unit.

NOTE: In case of shipping damage, your freight carrier should be notified

immediately.

2.2

Package Contents

•

Power chassis (hot-swappable Power Modules must be ordered
separately)

•

Instruction Manual (in bag)

•

Two removable 3-pin AC input wire clamp connectors (in bag)

•

Removable 7-pin alarm and temperature sensor wire clamp
connector (in bag)

•

Two removable 3-pin form-C alarm relay connector (in bag)

•

Plastic U-shaped safety cover with four 6-32 x 1/4-inch screws for
output bus bars (in bag)

•

Two rack-mounting ears (installed)

•

Six bolt/washer/nut sets for connections to the output bus bars (in
bag)

•

RJ11 data cable (ICT-JMP) (in bag)

•

Remote battery temperature sensor (ICT-TMP) included when a
BMMD is installed in the system (in bag)

«
...
13
14
15
16
17
...
»

Содержание Hybrid Ultra ICT-2U4-DC12


































































































Отзывы:

Нет отзывов