ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 97

ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 46

Hybrid Ultra

855-350-050_Rev2.0_Instruction Manual

Page

34

of 84

3.4

Status Indicators and Alarms

The status of the Hybrid Ultra is indicated on the front display panel module
on units equipped with an ICM, or via the network GUI (see Section 4) on
remotely monitored units. It is also available through  SNMP (see  Section
4.8.2).  Green  "POWER"  and  red  "FAULT"  LEDs  on  the  Power  Modules,
along  with  the  form-C  alarm  contacts  on  the  rear  panel  indicate  the  core
status of unit.

There is an option on the Setup & Control tab in the GUI for most alarms to
send an e-mail to designated addresses for remote notification (see Section
4.8.3).

All  alarms  and  warnings  will  be  displayed  on  the  front  display  screen  on
Hybrid Ultra systems and entered in the Alarm History log (most recent 20
alarms listed) (see Section 3.2.6).

Most  alarms  reset  automatically  when  the  trigger  condition  is  removed.
Major alarms such as a Module DC Output Failure or Module Configuration
Error require that the module be temporarily removed to cycle input power
and clear the fault.

Table 18. Power Module Alarms

(cont’d on next page)

Alarm

Condition

Trigger Condition

Module

Output

1

Red

LED

Green

LED

Alarm

Relay

Send

E-mail

2

Power Failure

Loss of AC power
to module

Disabled

Off

Off

Active

Yes

Module
Operating

Normal operation

Enabled

Off

On

No

-

Configuration
Error

Different voltage
modules installed

Enabled

Off

On

No

Yes

Current Limit
(Warning only,
display will
flash)

Output current
approaches within
1 A of the max
current limit setting

Enabled

Off

On

No

-

Fan Failure
(700 W)

Fan is not
operating to spec

Enabled

Off

On

No

Yes

Low Fan RPM
(1,500 W)

Fan is not
operating to spec

Enabled

Off

On

No

Yes

Fan Failure
(1,500 W)

Fan stops
spinning

Disabled

On

Off

Yes

Yes

Manual
Disable

Output switched
off by ICM or GUI

Disabled

Blink

Off

No

-

Module
Removal

Module system
connections open

Disabled

On

Off

No

-

«
...
44
45
46
47
48
...
»

Содержание Hybrid Ultra ICT-2U4-DC12


































































































Отзывы:

Нет отзывов