ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 97

ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 57

Hybrid Ultra

855-350-050_Rev2.0_Instruction Manual

Page

45

of 84

connected to the DC-DC Converter Module. The default setting varies
based on the DC-DC Converter Module installed (see Table 23).

Alarm Reporting

Send E-mail

: Select the check box to have an e-mail sent to the e-mail

addresses set up on the communications page whenever an alarm is
triggered on the integrated DC-DC Converter Module (see Section
4.8.3). The default setting is Disabled.

NOTE: Save Settings before leaving this tab.

4.5

Battery Backup

Use this tab to see the status of the connected batteries and to control their
settings.

The graphic will display green for an installed BMMD that is working as
expected; a red display for an installed module that has an active alarm; and
will be grey when a module is not installed in that slot.

CAUTION

Leave BMMD breaker turned off until the software has been
configured (see Section 3.2.2

or Section 4.5.2).

4.5.1

STATUS

This tab shows the operating status of the connected batteries.

Module Status

Shows the slot that the BMMD is installed in and the status (Alarm or OK).

«
...
55
56
57
58
59
...
»

Содержание Hybrid Ultra ICT-2U4-DC12


































































































Отзывы:

Нет отзывов