ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 97

ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 53

Hybrid Ultra

855-350-050_Rev2.0_Instruction Manual

Page

41

of 84

4.2.2

SETTINGS & CONTOL

This tab is used to adjust the System Output Settings.

DC Output Status

On/Off Buttons

: Use these to remotely disable the system output by

shutting off all Power Modules. The default setting is Enabled.

Auto-Restart Button

: Use this button to momentarily shut off the main

output, and then restart automatically after a time delay (set in the "Auto-
Restart Delay" field) This feature can be used to remotely force
connected equipment to re-boot.

Output Settings

Output Voltage

: Set the system "Output Voltage" to match the float

voltage requirement for the external battery. The default setting varies
based on the Power Modules installed (see

Current Limit

: Set the system output "Current Limit", to limit the total

current that can be drawn by all the external loads and charging the
battery. The default setting varies based on the Power Modules installed
(see Table 10).

Auto-Restart Delay

«
...
51
52
53
54
55
...
»

Содержание Hybrid Ultra ICT-2U4-DC12


































































































Отзывы:

Нет отзывов