IBM 865951Y - Netfinity 5000 - 51Y Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 220

background image

The default value is

Enabled. This value should not

be changed.

Boot Device Options

Select this choice to configure startable device
parameters. Before you can make updates, you must
know the ID of the device whose parameters you
want to configure.

SCSI Device Configuration

Select this choice to configure SCSI device
parameters. Before you can make updates, you must
know the ID of the device whose parameters you
want to configure.

Advanced Configuration Options

Select this choice to view or change the settings for
advanced configuration options. These options
include enabling support for large hard disk drives
and support for BIOS parameters if BIOS is enabled.

To reset to the the host adapter defaults, press F6; then,
follow the instructions on the screen.

SCSI disk utilities:

To see the IDs that are assigned

to each SCSI device, to format a SCSI device, or to scan
the disk for media defects, select SCSI Disk Utilities from
the SCSISelect Utility program menu.

To use the utility program, select a drive from the list.
Read the screens carefully before making a selection.

Note

If the following screen displays, you might have
pressed Ctrl

+

A before the selected drives were ready.

Restart the server, and watch the SCSISelect
messages as each drive spins up. After the drive that
you want to view or format spins up, press Ctrl

+

A.

à

ð

Unexpected SCSI Command Failure

Target SCSI ID:

4

SCSI CDB Sent:

ð3 ðð ðð ðð ðE ðð ð7 ðð ð2 ðð

Host Adapter Status:

ððh - No host adapter error

Target Status:

ð2h - Check condition

Sense Key:

ð2h - Not ready

+Sense Code:

ð4h

+Sense Code Qualifier:

ð2h

Press 'Esc' to continue.

á

ñ

Netfinity 5000 - Type 8659

53

«
...
59
60
61
62
63
...
»

Содержание 865951Y - Netfinity 5000 - 51Y





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 865951Y - Netfinity 5000 - 51Y

Бренд: VISIONARY DESIGNS Страницы: 2

Бренд: E-Medic Страницы: 31

BRIX GB-BACE-3150

Бренд: Gigabyte Страницы: 2

Бренд: Packard Bell Страницы: 122

Бренд: Elster Instromet Страницы: 89

Бренд: Rockwell Automation Страницы: 124

Бренд: Shuttle Страницы: 23

Бренд: Shuttle Страницы: 65

Бренд: Advantech Страницы: 19

Бренд: Shuttle Страницы: 2

Бренд: Veriton Страницы: 74

Бренд: ONKRON Страницы: 2

LYNX-6000 Series

Бренд: Portwell Страницы: 18

Бренд: Aaeon Страницы: 64

Бренд: Danacoid Страницы: 6

Бренд: Zenith Страницы: 150

Бренд: Baker Страницы: 57

Бренд: UMAX Technologies Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды