IBM 865951Y - Netfinity 5000 - 51Y Скачать руководство пользователя страница 66

Страница: 66 / 220

2. If you have not done so, remove the server cover.

See “Option installation” on page 125.

3. Remove the expansion-slot cover.

a. Release the slot retaining clamp by pulling the

curved arm on the clamp away from the system
board.

Note

The slot retaining clamp might differ slightly
from this illustration.

b. Remove the expansion slot cover from the slot

opening.

4. If the adapter is a full-length card, continue with this

step. Otherwise, go to step 5 on page 59.

a. Remove the card support bracket retaining clip.

b. If the adapter is a full length card in slot 1 or 2,

ensure that the card support bracket has the
appropriate card support installed for that slot.

Each card support is also identified on the tab as
ISA or PCI.

Card Type

Card Support Color

ISA

Black

PCI

White

Netfinity Server HMM

Содержание 865951Y - Netfinity 5000 - 51Y





























































































































































































































Результаты поиска

Содержание 865951Y - Netfinity 5000 - 51Y

Отзывы:

Похожие инструкции для 865951Y - Netfinity 5000 - 51Y

Бренды по названию

Популярные бренды

IBM 865951Y - Netfinity 5000 - 51Y, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание 865951Y - Netfinity 5000 - 51Y

Отзывы:

Похожие инструкции для 865951Y - Netfinity 5000 - 51Y

Бренды по названию

Популярные бренды