IBM 865951Y - Netfinity 5000 - 51Y Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 220

background image

PCNTNW-NW-165 The device was not found at IOADDRESS.

Explanation: The Ethernet controller cannot be found at the I/O address
specified.

Action: The Ethernet controller does not require a parameter for the I/O
address. Remove the I/O address parameter.

PCNTNW-NW-167 PCI scan specified, device not found.

Explanation: The driver cannot locate the Ethernet controller on the PCI bus.

Action: Verify that the PCI Ethernet device type is set to the default
(enabled) position in the Configuration/Setup utility programs (see “PCI bus
control” on page 30).

If the problem persists, go to “Diagnostic test programs” on page 10 to run the
diagnostic utility.

PCNTNW-NW-180 The DMA parameter is not necessary for PCI device.

Explanation: The Ethernet controller does not require a DMA setting.

Action: None necessary, message is for information only.

NDIS 2.01 (OS/2) driver messages:

The

following error messages are for the NDIS 2.01 (OS/2)
drivers. The explanation and recommended action are
included with each message.

PCNTND-1

Unable to open the Protocol Manager.

Explanation: The NDIS stack is not configured correctly.

Action: Check and correct the configuration.

PCNTND-6

Out of memory while allocating buffers.

Explanation: The driver could not allocate the requested buffers.

Action: Check the system configuration. Edit the PROTOCOL.INI file to
reduce the number of Txbuffers and Rxbuffers specified for the driver.

PCNTND-7

A Protocol Manager device error occurred.

Explanation: The NDIS stack is not configured correctly.

Action: Check and correct the configuration.

PCNTND-8

Bad status for the Protocol Manager.

Explanation: The NDIS stack is not configured correctly in the
PROTOCOL.INI file.

Action: Check and correct the configuration.

PCNTND-9

Cannot find the PROTOCOL.INI entry.

Explanation: The NDIS stack is not configured correctly in the
PROTOCOL.INI file.

Action: Check and correct the configuration.

PCNTND-10

The Protocol Manager Input Output Control (IOCTL)
failed.

Explanation: The NDIS stack is not configured correctly in the
PROTOCOL.INI file.

Action: Check and correct the configuration.

PCNTND-11

Protocol Manager registration failed.

Explanation: The NDIS stack is not configured correctly.

Action: Check and correct the configuration.

36

Netfinity Server HMM

«
...
42
43
44
45
46
...
»

Содержание 865951Y - Netfinity 5000 - 51Y





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 865951Y - Netfinity 5000 - 51Y

Бренд: Oldfields Страницы: 2

Бренд: ZiLOG Страницы: 166

Бренд: IBM Страницы: 102

Бренд: Medion Страницы: 88

Бренд: ZIEHL-ABEGG Страницы: 84

Бренд: Acrosser Technology Страницы: 17

Бренд: Advantech Страницы: 68

6005 - Pro Microtower PC

Бренд: Compaq Страницы: 4

Бренд: NEC Страницы: 127

Бренд: Acer Страницы: 120

Бренд: Allen-Bradley Страницы: 34

Бренд: Moxa Technologies Страницы: 65

ERGOLUX ELRIPLGDKBA

Бренд: Kogan Страницы: 16

ERGOLUX ELDUALMTWHA

Бренд: Kogan Страницы: 20

Бренд: Shuttle Страницы: 2

Бренд: Alpha Microsystems Страницы: 63

Бренд: AMSTRAD Страницы: 31

Бренд: VarTech Systems Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды