IBM 865951Y - Netfinity 5000 - 51Y Скачать руководство пользователя страница 88

Страница: 88 / 220

Completing the rack model installation

1. Replace the top cover:

a. Align the top cover with the top of the server,

about 25 mm (1 inch) from the front of the
server.

b. Hold the cover against the server and slide the

cover toward the front of the server until the
cover clicks into place.

Note

Be sure the front edge of the cover is flat
against the server.

c. Turn the captive thumbscrew

.1/

until the cover

is secured.

2. Replace the bezel, if it was removed.

a. Place the bezel tabs

.2/

in the slots at the left

front of the server.

b. Press the right end of the bezel toward the

server front until the bezel clicks into place.

Netfinity Server HMM

Содержание 865951Y - Netfinity 5000 - 51Y





























































































































































































































Результаты поиска

Содержание 865951Y - Netfinity 5000 - 51Y

Отзывы:

Похожие инструкции для 865951Y - Netfinity 5000 - 51Y

Бренды по названию

Популярные бренды

IBM 865951Y - Netfinity 5000 - 51Y, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание 865951Y - Netfinity 5000 - 51Y

Отзывы:

Похожие инструкции для 865951Y - Netfinity 5000 - 51Y

Бренды по названию

Популярные бренды