HP Integrity rx2660 Скачать руководство пользователя | Manualshive

Страница: 98 / 254

background image

1.

Log in to OpenVMS running on the server that you want to shut down.

Log in to the iLO 2 MP for the server and use the Console menu to access the system console.
Accessing the console through the iLO 2 MP enables you to maintain console access to the
server after HP OpenVMS has shut down.

2.

At the

OpenVMS DCL

prompt issue the

@SYS$SYSTEM:SHUTDOWN

command and specify

the shutdown options in response to the prompts given.

$@sys$system:shutdown

SHUTDOWN -- Perform an Orderly System Shutdown
on node NODE1

How many minutes until final shutdown [0]:
Reason for shutdown [Standalone]:
Do you want to spin down the disk volumes [NO]?
Do you want to invoke the site-specific shutdown procedure [YES]?
Should an automatic system reboot be performed [NO]?
When will the system be rebooted [later]:
Shutdown options (enter as a comma-separated list):
REMOVE_NODE Remaining nodes in the cluster should adjust quorum
CLUSTER_SHUTDOWN Entire cluster is shutting down
REBOOT_CHECK Check existence of basic system files
SAVE_FEEDBACK Save AUTOGEN feedback information from this boot
DISABLE_AUTOSTART Disable autostart queues
POWER_OFF Request console to power-off the system
BIB_STATE Request console to reboot all CPUs to the Itanium BIB state

Shutdown options [NONE]: REBOOT_CHECK

%SHUTDOWN-I-BOOTCHECK, performing reboot consistency check...
%SHUTDOWN-I-CHECKOK, basic reboot consistency check completed

%SHUTDOWN-I-OPERATOR, this terminal is now an operator's console
%SHUTDOWN-I-DISLOGINS, interactive logins will now be disabled
%SET-I-INTSET, login interactive limit = 0, current interactive value = 1
%SHUTDOWN-I-SHUTNET, the DECnet network will now be shut down

NOTE:

HP OpenVMS I64 currently does not support the

POWER_OFF

shutdown option.

Due to the type of server you purchased, your output may not exactly match the output
shown here.

Booting and Shutting Down Microsoft Windows

This section describes how to boot and shut down Microsoft Windows on entry-class HP Integrity
servers and how to add Windows entries to the system boot options list.
•

“Adding Microsoft Windows to the Boot Options List” (page 98)

•

“Booting the Microsoft Windows Operating System” (page 100)

•

“Shutting Down Microsoft Windows” (page 101)

Adding Microsoft Windows to the Boot Options List

To add a Microsoft Windows entry to the system boot options list you must do so from EFI by
using the

\MSUtil\nvrboot.efi

utility to import boot options from the

EFI\Microsoft\WINNT50\Boot00...

file on the device from which Windows is loaded.

This procedure adds the Microsoft Windows item to the boot options list.

98

Booting and Shutting Down the Operating System

«
...
96
97
98
99
100
...
»

Содержание Integrity rx2660































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Integrity rx2660

Бренд: 3idee Страницы: 5

Бренд: 3idee Страницы: 5

Бренд: 3idee Страницы: 7

Бренд: Hama Страницы: 22

Бренд: TRENDnet Страницы: 40

Бренд: Clarion Страницы: 15

PowerLife 3LR12P1B

Бренд: Philips Страницы: 2

LightMaster PLC-KNX

Бренд: Philips Страницы: 2

Home Power SPS3102WB/37

Бренд: Philips Страницы: 2

LIGHTOLIER IS-LLAH11

Бренд: Philips Страницы: 4

Бренд: Edimax Страницы: 19

VELOCITY NP900n

Бренд: NetComm Страницы: 6

POWERLINE NP504

Бренд: NetComm Страницы: 6

Бренд: NetComm Страницы: 2

Бренд: NetComm Страницы: 2

Бренд: Compaq Страницы: 22

Бренд: d&b audiotechnik Страницы: 6

Бренд: d&b audiotechnik Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды