HP Integrity rx2660 Скачать руководство пользователя

Страница: 105 / 254

Access the EFI System Partition for the SuSE Linux Enterprise Server boot device.

Use the

map

EFI Shell command to list the file systems (

fs0

fs1

, and so on) that are known

and mapped.

To choose a file system to use, enter its mapped name followed by a colon (

). For example,

to operate with the boot device that is mapped as

fs3

, enter

fs3:

at the EFI Shell prompt.

Enter

ELILO

at the EFI Shell command prompt to launch the

ELILO.EFI

loader.

If needed, you can specify the loader path by entering

\efi\SuSE\elilo

at the EFI Shell

command prompt.

Allow the

ELILO.EFI

loader to proceed with booting the SuSE Linux kernel.

By default, the

ELILO.EFI

loader boots the kernel image and options specified by the

default item in the

elilo.conf

file.

To interact with the

ELILO.EFI

loader, interrupt the boot process (for example, enter a

space) at the

ELILO boot

prompt. To exit the loader, use the

exit

command.

Shutting Down Linux

Use the

shutdown

command to shut down Red Hat Enterprise Linux or SuSE Linux Enterprise

Server.

The Red Hat Enterprise Linux and SuSE Linux Enterprise Server

shutdown

command has the

following options:

-h

Halts (power off) after shutdown.

Use the

command at the iLO 2 MP Command menu to manually power on or power

off server hardware, as needed.

-r

Reboots after shutdown.

-c

Cancels an already running shutdown.

time

When to shut down. (Required.) You can specify time in any of the following ways:
•

Absolute time in the format hh:mm,; hh is the hour (one or two digits) and mm is the
minute of the hour (two digits).

•

Number of minutes to wait in the format

m, in which m is the number of minutes.

•

now

to immediately shut down; this is equivalent to using

to wait zero minutes.

For details, see the shutdown (8) Linux manpage. Also see the Linux manpage for the

poweroff

command.
1.

From the command line for Red Hat Enterprise Linux or SuSE Linux Enterprise Server, issue
the

shutdown

command to shut down the operating system.

Issue the

shutdown

command with the desired command-line options, and include the

required time argument to specify when the operating system shutdown is to occur.

For example,

shutdown -r +20

shuts down and reboots the server in twenty minutes.

Booting and Shutting Down Linux

105

Содержание Integrity rx2660































































































































































































































































Результаты поиска

Содержание Integrity rx2660

Отзывы:

Похожие инструкции для Integrity rx2660

Бренды по названию

Популярные бренды

HP Integrity rx2660, Руководство пользователя и обслуживания

Результаты поиска

Содержание Integrity rx2660

Отзывы:

Похожие инструкции для Integrity rx2660

Бренды по названию

Популярные бренды