Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 10

Страница: 10 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

4.3 Accessories

A range of accessories are available to allow use of Sensepoint XCD RFD in a wide

variety of applications. These include Pipe mounting bracket, Sunshade deluge cover,

Sensor collecting cone, Sensor flow Housing and Remote sensor mounting junction

boxes.

For Sensepoint XCD

(P/N: SPXCDWP)

For Sensepoint / 705

(P/N: 02000-A-1640/1635)

Calibration Cup

Standard Weather Protection

The Standard Weather Protection is designed to

protect the sensor from changes in environmental

conditions. This is recommended to be fitted to

a Sensepoint XCD sensor and Sensepoint /

705 sensors.

The Gassing Cap (P/N: S3KCAL) is an optional

accessory that may be temporarily fitted to

Sensepoint XCD flammable sensors for Gas

Response checking during commissioning and

routine maintenance.

For UL/CSA Junction Box

(P/N: 2430-0021)

For ATEX Junction Box

(P/N: 00780-A-0100)

For Sensepoint XCD

(P/N: SPXCDCC)

For Sensepoint / 705

(P/N: 02000-A-1642)

Remote Sensor Mounting

Collecting Cone

UL aluminum junction box, ATEX standard junction box and

ATEX High temperature junction box (P/N: 2052D0001) are

optional accessories that can be used for remote sensor

mounting. Make the connection from the junction box to

the transmitter using suitable cable and cable glands.

The Collecting Cone is an optional accessory

that may be fitted to the Weather Protection

of XCD and Sensepoint / 705 sensors.

The collecting cone is designed for use with

gases that are lighter than air.

Sensepoint Filter and Filter Housing

Calibration Gas Flow Housing

Sensepoint Stainless steel filter (P/N: 00780-

F-0018) and Filter Housing (P/N: 00780-C-

0038) is an optional accessory can be used to

offer additional protection to the Sinter in dry,

and dusty applications.

The Calibration Gas Flow Housing (P/N: 02000-

A-1645) may be used for either calibration of the

Sensepoint / 705 sensor or if the Sensepoint /

705 sensor is to be used as part of a Aspirated

Sampling System.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды