Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 6

Страница: 6 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

Locking

Grub

screw

Internal Earth

Point

Enclosure

External Earth

Point (x2)

M20 or 3/4"NPT cable/conduit entries

(x2)

Cover

Seal

Display Module

Terminal Module

Ex d Plug

Integral

mounting plate

Certification Label

M25 or 3/4"NPT entry for

Flammable Sensor or Remote Sensor Cable Gland

4 Introduction

The Sensepoint XCD RFD (“Exceed RFD”) transmitter allows the user to either directly

or remotely mount a flammable gas sensor from the Sensepoint XCD , Sensepoint and

705 sensor ranges. The remote sensor can be located up to 30 meters (100 feet) from

the transmitter. The transmitter features a display and three programmable relays for

controlling external equipment e.g. alarms, sirens, valves or switches. The transmitter

provides an industry standard 3-wire, 4-20mA source or sink output for connection to a

dedicated gas detection control system or PLC.

The construction of Sensepoint XCD RFD allows it to be used in hazardous area locations;

it may also be used in other areas not classified as hazardous. Sensepoint XCD RFD is

suitable for use in Zone 1 or 2 hazardous areas (International).

Calibration and maintenance is carried out using a Magnetic Wand, this allows a single

user to undertake routine maintenance without needing to access internal components.

Sensepoint XCD RFD comprises of the main parts as shown below.

Diagram 1. – Exploded View

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды