Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 36

Страница: 36 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

12.2 Replacing Modules within the Transmitter

Two replaceable module assemblies are located within the transmitter housing. The

Display Module and the Terminal Module.

The Display Module is simply removed by unplugging it from the Terminal Module (this

procedure is done during normal installation).

To replace the Terminal Module, use the following procedure:

1. Unscrew and remove the Transmitter Cover

2. Lift the handle and un-plug and remove the Display

Module.

3. Unplug the connection terminals and lift them clear of the

Terminal Module.

4. Unplug the connector for the XCD sensor.

5. Loosen and remove the three “cross-headed” screws that

secure the Terminal Module to the Transmitter housing.

6. Carefully lift the Terminal Module from the transmitter

housing.

7. Fit the new Terminal Module using the above procedure in

reverse order.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды