Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 37

Страница: 37 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

12.3 Faults and Warnings

The table below provides details of possible error.

Message

Description

Action

W-01

Calibration needed

The unit has not been calibrated for the

configured calibration interval

Calibration is necessary due to change

of sensor/gas type

W-02

Transmitter Temperature

limits exceeded

Use ‘



’ to clear when within limits

W-03

Alarm setting needs to be

configured

Re-configure alarm settings such that

upper alarm should not exceed user

configured scale

W-04*

Over-range warning

Use ‘



’ to clear when within limits

W-05*

The sensor is switched off

to prevent it from being

deteriorated

Make sure that there is no flammable

gas in the air and use ‘



’ to clear when

within limits

F-01

Internal I2C failure

Cycle power to detector. Replace

detector

F-02

Cell failure

For Flammable/IR, cycle power to

detector. Replace sensor

F-03

Significant zero drift

Re zero/calibrate

F-04

Unexpected sensor fitted

Replace sensor

F-05

EEPROM is corrupted

Reset transmitter. If fault still appear,

replace transmitter

F-06

Low supply voltage

Reset transmitter. If fault still appear,

replace transmitter

F-07

SRS processor failure

Reset transmitter. If fault still appear,

replace transmitter

F-08

RAM read/write fault

Reset transmitter. If fault still appear,

replace transmitter

F-09

Info. memory corrupted

Reset transmitter. If fault still appear,

replace transmitter

F-10

Code Memory corrupted

Reset transmitter. If fault still appear,

replace transmitter

F-11

DAC output failure

Check load resistor or sink/source mode

switch was configured properly

F-12

Heater failure

Reset transmitter. If fault still appear,

replace transmitter

F-13

Supplied voltage failure

Check supply voltage. Replace detector

*Note : W-04 and W-05 are only for flammable catalytic bead sensors. For other gases, gas reading will blink on the LCD

instead of the over-range warning.

Table 9: Fault and Warning List

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды