Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 17

Страница: 17 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

6 Electrical connections

WARNINGS

Sensepoint XCD RFD is designed for installation and use in Zone 1 or 2 hazardous areas

in many countries including Europe, and for Class I, Division 1, Group B,C & D Hazardous

Areas in the Americas.

Installation must be in accordance with the recognized standards of the appropriate

authority in the country concerned.

Access to the interior of the detector, when carrying out any work, must only be conducted

by trained personnel.

Before carrying out any work ensure local regulations and site procedures are followed.

Appropriate standards must be followed to maintain the overall certification of the detector.

Care should be taken when removing and refitting the Sensepoint XCD Sensor Cartridge to

the Sensor Socket so that damage to the connection pins can be avoided.

If using an anti-seize compound, the threads should be thinly coated with an approved

silicone free compound e.g. petroleum jelly

To reduce the risk of ignition of hazardous atmosphere, de-classify the area or disconnect

the equipment from the supply circuit before opening the detector enclosure. Keep

assembly tightly closed during operation.

Never attempt to open a junction box/enclosure or replace/refit the sensor in potentially

hazardous atmospheres while power is still applied to the transmitter.

The detector must be earthed/grounded for electrical safety and to limit the effects of

radio frequency interference. Earth/ground points are provided inside and outside the unit.

Ensure that all screens/instrument earth/clean earth wiring is earthed/grounded at a single

point (either at the controller or detector - BUT NOT BOTH) to prevent false alarms due to

earth/ground loops.

Take care when handling sensors as they may contain corrosive solutions.

Do not tamper with or in any way disassemble the sensor.

Do not expose to temperatures outside the recommended ranges.

Do not expose sensors under storage conditions to organic solvents or flammable liquids.

Refer to the local or national regulations relative to the installation at the site. For Europe

see EN60079-29-2, EN60079-14 and EN61241-14. For the Americas refer to the Sensepoint

XCD RTD Control Drawing 3001EC091 shown in section 17.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды