Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 12

Страница: 12 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

(MODBUS ID SETTING)

Set id>>Set Modbus slave ID>>Set Baud rate>>Set Parity

1) Slave ID shall be set 1~247

2) Baud rate setting 9600 or 19200

3) Parity setting (No, Even, Odd)

From the Configuration Mode screen, select‘



’. To set the Modbus Slave ID, use the

up-down ‘



’switches to move to the desired position and use ‘



’to select it. Again,

using the‘



’switches, increment or decrement the value until the desired value appears,

selects the value and moves to the next setting.

The communications baud rate and Parity Setting can also be set from this screen by

using the‘



’ switches to navigate to the baud rate display then selecting ‘



’. Using the

‘



’switches, highlight the proper baud rate or parity setting and select‘



’. Default is

Slave ID 1, 19200bps and even parity.

Note: Set ID menu is available only for XCD equipped with Modbus

option.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды