Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 34

Страница: 34 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

12 Servicing

12.1 Sensor replacement

The sensors that are used with the Sensepoint XCD RFD have no serviceable parts.

When they have reached the end of their operational life, simply replace the sensor or the

sensor cartridge.

Diagram 13: Sensor Replacement

Only a qualified installation engineer should service the sensor. Ensure power is off before

carrying out any maintenance procedures. The only maintenance required is sensor

replacement and filter changing (if fitted to an accessory). To replace the complete sensor

refer to the Quick Start Guide of Sensepoint XCD Remote Cartridge (PN: 3001M5022_1).

Caution: The following procedure should be followed carefully and only performed by

suitably trained personnel.

A fault condition will be signalled by the detector if the sensor is removed with the unit

under power.

WARNINGS

Take care when handling sensors as they may contain corrosive solutions. Do not tamper

or in any way dis-assemble the sensor. Do not expose to temperatures outside the

recommended range. Do not expose sensor to organic solvents or flammable liquids.

Care should be taken when removing and refitting the Sensepoint XCD plug-in Sensor

Cartridge to the Sensor Socket so that damage to the connection pins can be avoided.

Socket Housing

Main body of sensor

Fiter

Black plastic retainer

Sensor Cartridge

Sensor Retainer

with locking screw

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды