Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 15

Страница: 15 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

5.3 Installing the sensor

WARNINGS

Care should be taken when removing and refitting the Sensepoint XCD plug-in Sensor to

the Sensor Socket so that damage to the connection pins can be avoided.

If using an anti-seize compound, the threads should be thinly coated with an approved

silicone free compound e.g. petroleum jelly

Take care when handling old sensors as they may contain corrosive solutions.

Take care when removing or replacing the Sensor Retainer as there may be sharp edges

present on the adjoining threads.

The equipment is designed and constructed as to prevent ignition sources arising, even in

the event of frequent disturbances or equipment operating faults.

Only assessed for ATEX for ignition hazards.

The sensor head must be fitted with the supplied weather protection, and mounted so that

the sinter is pointing downward to provide ingress protection IPX6.

The weather protection is a potential electrostatic charging hazard. The manufacturer’s

instructions should be observed.

A remotely mounted sensor should be mounted using a suitable junction box . For further

details regarding mounting sensors to suitable junction boxes refer to the relevant sensor

manual.

1. Connect the remote sensor/junction box to the Sensepoint XCD RFD transmitter

using suitable cable with wires of diameter 0.5 - 2.5mm

(20AWG - 13AWG).

2. Connect the cable to the transmitter enclosure via the bottom entry.

3. Cable (non conduit) based installations must use appropriately certified cable glands.

Refer to the Sensepoint XCD RFD Control Drawing 3001EC091 shown in section 17

for conduit based installation in the Americas.

Note: The maximum cable length between the remotely mounted sensor and the

Sensepoint XCD RFD transmitter is 30 meters (100 feet). The maximum loop

resistance is 17 Ω.

4. Terminate the wires from the sensor in the transmitter as shown in chapter 6.2.

5. Select sensor type at configuration menu after remote sensor mounting. Refer to the

chapter 12.1 Sensor Replacement and the chapter 13.3.1 Sensor Selection.

Cable Gland

Sensor

Transmitter

Junction Box

Sensepoint XCD RFD with Sensepoint Remote Sensor

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды