Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 21

Страница: 21 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

6.4 Cabling

The use of industrial grade, suitably armoured field cable is recommended.

For example, screened 3 cores (plus screen 90% coverage), suitably mechanically

protected copper cable with a suitable M20 explosion-proof gland with 0.5 to 2.5 mm2 (20

to 13 AWG) conductors. Ensure the cable gland is installed correctly and fully tightened.

All unused cable entries must be sealed with a suitable certified sealing plug (one plug is

supplied).

Remote Mounting Cable Details

Type

Cable Spec

Max Length

RFD Remote

AWM2464 AWG20~AWG14 Shield

30meters

6.5 Cable and Earth/Ground regimes

Effective Earth/Ground bonding is important to ensure good EMC and RFI immunity.

The following diagrams show examples of how to earth/ground bond the cable at

enclosures. These bonding techniques provide good RFI/EMC performance. Earth/ground

loops must be avoided to prevent the risk of false signal variation.

Cable to Transmitter

Diagram 8: Controller Grounding

Diagram 9: System grounding

Cable outer sheath

Cable inner sheath

Clean / Instrument

Earth Screen

Controller

Power & Signal

Earth Screen

Controller

Transmitter

Note: The Sensepoint HT sensor requires an earth core if the remote junction box does

not have a suitable earth point.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды