Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 14

Страница: 14 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

5.1 Mounting and location

Gas detectors should be mounted where a potential hazard of gas is most likely to be

present. The following points should be noted when locating gas sensors.

• When locating detectors consider the possible damage caused by natural events e.g.

rain or flooding.

• Consider ease of access to the gas detector for functional testing and servicing.

• Consider how escaping gas may behave due to natural or forced air currents.

Note: The placement of gas detectors should be determined following the advice of

experts having specialist knowledge of gas dispersion, experts having knowledge of

the process plant system and equipment involved, safety and engineering personnel.

The agreement reached on the location of detectors should be recorded.

5.2 Mounting the transmitter

The Sensepoint XCD RFD transmitter has an integral mounting plate consisting of four

mounting holes on the transmitter body. The transmitter may be fixed directly to a surface

mounting, or to a horizontal or vertical pipe/structure, 40.0-80.0mm (1.6 to 3.1 inches) in

diameter/cross section. The Pipe Mounting Bracket accessory (optional accessory) may

be used for this purpose.

Caution: The location of gas detectors should be made in accordance with any relevant

local and national legislation, standards or codes of practice. Always replace sensors

with a sensor of the same type.

Diagram 5: Outline and mounting dimensions

All dimensions are

shown in mm.

M20 or 3/4 NPT entries

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды