Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 26

Страница: 26 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

8.3 Magnetic Wand Activation

The magnetic wand is used as a tool to allow the user

to communicate with the Sensepoint XCD RFD transmitter.

Communication with the XCD RFD is achieved by positioning

the Magnetic Wand at one of three different positions on

the front glass window of the Sensepoint XCD RFD transmitter.

Activation of the switches is verified by observing

the Magnetic Wand Activation Icon on the LCD display

Hold the Magnetic Wand in position for up to 2 seconds

Hold the Magnetic Wand in position for 3 seconds or more =

8.4 Operation Mode Structure

Sensepoint XCD RFD has 3 operating modes.

Monitoring mode

, is the normal operating status while XCD RFD measures and

displays gas concentration. The fault/warning status is periodically checked, relay

contacts are activated according to the configuration.

Configuration mode

, this mode allows parameters relating to the configuration of

the Transmitter functions to be changed according to specific needs. This mode can

be protected by a password mechanism to prevent unauthorised changes being

made.

Review mode

, allows the user to view the current configuration settings.

Diagram 11: Mode Structure

Further details of the information available and configuration options for the Sensepoint

XCD RFD can be found in Section 13. of this manual.

Start - Up

Configuration

Mode

Review

Mode

Monitoring

Mode

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды