Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 45

Страница: 45 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

Ir-5*

CO2

Ir-7

Methane

mEt

Ir-8*

Propane

ProP

*Contact Honeywell Analytics for availability

Gas selection is dependent on the type of sensor attached to the XCD RFD. If Ir-7 sensor

is attached, then a user can only select ‘mEt’ gas respectively. But when Cb-3/Cb-4 sensor

is attached to the XCD RFD, a user can select the gas from Str1 (1*) to Str8 (8*). For more

information on star rating, please refer to section 19.2.

The current configuration of the XCD RFD is displayed and by using the ‘



’ switch to enter

“SEL gAS” menu. To select a flammable gas, use ‘



’ to move through the list, and then

use ‘



’ to make the selection or abort function to discard the selection and return to menu

mode.

If type of gas is changed, calibration prompt will appear to ask if you want to perform

calibration.

...

Diagram 16: Gas Selection

CAUTION

The 4-20mA analogue output signal will remain INHIBITED at 2mA (default setting) while the

XCD RFD remains in Configuration Mode. However, the ALARM and FAULT RELAYS remain

Active.

Changing the configuration of the Sensor Type or the Gas Star Rating for catalytic sensors

may result in temporary activation of the ALARM or FAULT RELAYS.

Should this occur, then recalibrating the sensor will return the XCD RFD to normal condition

and reset the relays.

As a precaution, please take necessary action to manually inhibit any external actuator or

alarm devices that are connected to the XCD RFD Alarm/Fault Relays to prevent unnecessary

activation during commissioning or reconfiguration of the XCD RFD gas detector.

For CSA Certified applications, use CB-6 calibrated only to Methane.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды