Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 11

Страница: 11 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

4.4 Options
4.4.1 Modbus

One of the most common field buses in the industry, the optional Modbus

interface allows

the XCD to connect to a bus of devices and transmit data to PLCs or controllers (see

Appendix A). Connections to the XCD are made through a pluggable terminal block on

the Modbus

interface circuit board. Modbus

RTU protocol uses ASCII/Hex protocols for

communication. And allows all transmitter/sensor front panel functions to be transmitted

using this industrial fieldbus.

Modbus

protocol is a Master-Slaves protocol. Only one master (at the same time) is

connected to the bus and one or up to 32 slave nodes are also connected to the same

serial bus. Modbus

communication is always initiated by the master. The slave nodes will

never transmit data without receiving a request from the master node. The slave nodes

will never communicate with each other. The master node initiates only one Modbus®

transaction at the same time.

The MODBUS

may only be used for data collection or record keeping with regard to

combustible gas detection and not for performance verification.

Modbus

option is available only for selected gases. Please refer to chapter 15 Ordering

information.

To find out if a unit has the Modbus

option fitted, look at the part number on the product

label. Units fitted with Modbus

have the letter “M” at the end of the part number.

Note: MODBUS

is a registered trademark of Schneider Automation Inc.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды