Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 3

Страница: 3 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

2 Information

This manual is for use with the Sensepoint XCD RFD range transmitters only.

The Start-up/Surge/In rush current is dependant on the type of power supply used. The

typical start-up current for Sensepoint XCD RFD is less than 800mA. Measure the start-

up current using the specific power supply before installation to ensure suitability for your

application.

Honeywell Analytics can take no responsibility for installation and/or use of its equipment if

not done so in accordance with the appropriate issue and/or amendment of the Technical

Manual.

The reader of this Operating Manual should ensure that it is appropriate in all details

for the exact equipment to be installed and/or operated. If in doubt, contact Honeywell

Analytics for advice.

The following types of notices are used throughout this Operating Manual:

WARNING

Identifies a hazardous or unsafe practice which could result in severe injury or

death to personnel.

Caution: Identifies a hazardous or unsafe practice which could result in minor injury

to personnel, or product or property damage.

Note: Identifies useful/additional information.

Every effort has been made to ensure the accuracy of this document; however, Honeywell

Analytics can assume no responsibility for any errors or omissions in this document or

their consequences.

Honeywell Analytics would greatly appreciate being informed of any errors or omissions

that may be found in the content of this document.

For information not covered in this document, or if there is a requirement to send

comments/corrections about this document, please contact Honeywell Analytics using the

contact details given on the back page.

Honeywell Analytics reserve the right to change or revise the information supplied

in this document without notice and without obligation to notify any person or

organization of such revision or change. If information is required that does not

appear in this document, contact the local distributor/agent or Honeywell Analytics.

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды