Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 9

Страница: 9 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

4.2.3. 705 LEL Flammable gas sensors (UL Approved)

Standard LEL version

The standard LEL sensor is available for use in temperatures up to 80°C (remote mounting

only) and detects gas concentrations up to 100% LEL of a target gas with a resolution in

the region of 1% LEL, depending on the gas being detected. The sensor is available with

¾”NPT thread only.

High Temperature LEL version

The high temperature version is available for use in temperatures up to 150°C (remote

mounting only) and detects gas concentrations up to 100% LEL of a target gas with a

resolution in the region of 1% LEL, depending on the gas being detected. The sensor is

available with ¾”NPT thread only.

Details of connecting these sensors with the Sensepoint XCD RFD transmitter are given

in sections 5 and 6. For more sensor specific details, refer to the 705 Combustible Gas

Sensor Operating Instructions Part No: 00705M5002.

Standard LEL version High Temperature LEL version

705 LEL flammable sensors

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды