background image

Thank you for purchasing i3 International’s H59 LPR IP bullet camera.

H59 is equipped with a motorized 7-22mm @ F1.6 (H59B7) or 2.8-12mm @ F1.4 

(H59B2) lens. This camera series is compatible with the optional recommended 

mounting base (Part#: B59). H59-camera series is an Edge LPR camera that is an 

integral part of i3’s Velocity Timer Solution (VTS). 

Visit www.i3international.com for more information about VTS.

Model

Application Use

H59B7

i3 Velocity Timer / CMS: Loyalty Report, Curbside Pickup, 

Pre-menu “Danger Zone” monitoring.

H59B2 / H59B7

SRX-Pro Server v7+, Gate Access Control

Note: 

h.265 codec is supported by SRX-Pro v7 and above only. For backwards 

compatibility, change the codec to h.264 in the camera’s web settings > Config > 

Image > Video/Audio > Video Compression.

SAFETY

When installing your H59 camera be sure to avoid:

•  excessive heat, such as direct sunlight or heating appliances

•  contaminants such as dust and smoke

•  strong magnetic fields

•  areas with mechanical vibrations

•  fluorescent lamps or objects that reflect light and unstable light sources

•  temperatures below -30° C (-22° F) and above 60° C (140° F

).

To avoid electrical shock and to preserve the product warranty, 

DO NOT

 

disassemble the camera. Refer servicing to qualified personnel only.

POWER SUPPLY

This camera accepts PoE and DC12V power.

Ensure the supplied voltage meets the power consumption requirements of this 

camera (11W) before powering the camera on. Incorrect voltage may cause 

irreparable damage to the video camera and will effectively void the camera 

warranty. 

CLEANING

•  For maximum optical clarity, the camera dome or lens must remain clean. 

Use a soft, dry cloth to remove finger prints or dust from the dome cover.

•  Use a blower to remove dust from the lens.

•  Do not use volatile solvents such as alcohol, benzene, or thinners, 

as they may damage the surface finishes. 

PACKAGE CONTENTS

Ensure that the items received match  

those listed on the order form and 

the packing slip. In addition to this 

manual and a fully assembled camera,

the dome camera packing box includes:

A. 

Standard RJ45 Connector x2 

B. 

Torx bit x1 

C. 

Surface Mount template x1

D. 

Plastic Anchor x4 

E. 

Round Head Screw (Tapping Type) x4

CAMERA PARTS AND DIMENSIONS

C

A

D

2MP H.265 Bullet LPR Camera

H59B2 / H59B7

User Manual

i3-TRNG-CAMS-

H59

.indd

B

  

  

 

6

1. 

Sun shield adjustment screw (Phillips). Unscrew to pull the shield forward to 

increase lens shading, if required. Re-tighten when done.

2. 

Mounting holes (x4)

3. 

Access panel cover, secured with two Phillips screws. Remove to access Tele/Wide 

lens adjustment buttons, microSD card slot, and CVBS monitor connection port.

4. 

Three-axis adjustment screws (torx). Adjust the mounting assembly position for the 

perfect angle. See 

Installation Recommendations

 section for more information.

5. 

12VDC power connector (optional).

6. 

RJ45 Ethernet PoE Port with waterproof RJ45 connector assembly. 

Insert an Ethernet cable into the port for network connection as well as PoE 

(Power over Ethernet) power. Use the included waterproof RJ45 connector assembly 

to maintain the camera warranty and the water-resistant rating.

7. 

MicroSD Card slot for on-camera video storage (up to 256GB supported, sold 

separately).

8. 

Tele/Wide lens adjustment buttons. Motorized lens can also be adjusted remotely 

through Video Pilot Client.

9. 

CVBS hand-held monitor connection port

10. 

Reset button. Press for 10 seconds to restore camera settings to factory defaults. 

11. 

Light sensor (do not block or obstruct) 

INSTALLATION

Use the mounting instructions provided with the B59 (optional mounting base) mount to 

mount the camera.

1

Figure 3. H59, Parts and Dimensions

Figure 1. H59, Accessories

WATERPROOF RJ45 ASSEMBLY

 

To prevent the corrosion of the RJ45 connector and to maintain the camera 

warranty, use the RJ45 waterproof assembly attached to the camera, as shown in 

the diagram below.

1

2

3

1. 

Twist off the RJ45 waterproof 

assembly from the RJ45 

connector.

2. 

Feed the CAT5e/6 cable through 

the opening in the connector and 

crimp it using the standard RJ45 

connector provided.

3. 

Plug the crimped CAT5e/6 cable 

into the RJ45 connector on the 

camera and twist the waterproof 

assembly on to re-attach it.

Figure 2. Waterproof RJ45  connector

15

/

16

” (100.3 mm)

7

/

16

” (88.9 mm)

11” (279.5 mm)

9

/

16

” (64.6 mm)

9

/

16

” (64.6 mm)

3

3

7

8

9

10

E

5

11

4

NOT

IN

USE

  

ALAR

M

 4 

3 2

 1

2

Rev. 220819

Figure 4. H59 mounting diagram using optional B59 mounting base.

1

2

3

4

Отзывы: