Honeywell Sensepoint XCD RFD Скачать руководство пользователя страница 25

Страница: 25 / 79

Sensepoint XCD RFD Technical Manual

SPXCDHMRFEN Issue 4_08-2016

8.2 System Status

Display indications, current output and relay states for various operational conditions

are shown in the following table. For further details of error messages and trouble shooting

see section 12.3.

System Status

Status

Display

Current Output

Relay

Back

Light

Fault

Fault:

Circuit or sensor

error

F-XX

fault number

with fault icon

blinking

0-1.0 mA



Yellow,

flashing

System Fault

N/A

0-0.15mA

Note: In the event of processor failure the watchdog will automatically reset the system for

recovery.

Warning

W-XX

warning number

with fault icon

blinking

Dependent on

system status

Green

Steady

Normal

0.0

Gas

concentration

4-20 mA

Green

Steady

Alarm 1

Gas

concentration.

alarm icon

blinking

4-20 mA



Red,

flashing

Alarm 2

Gas

concentration.

alarm icon

blinking

4-20 mA



Red,

flashing

Over-range

Full scale icon

and reading

blinking

22mA



Red,

flashing

Inhibit

Inhibit icon

dependent

on Menu

command. If

any relay is set

to inhibit relay,

then inhibit relay

will be activated.

2 or 4mA

depending on

configuration.

Green

Steady

Table 4: System status

Содержание Sensepoint XCD RFD
















































































Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RFD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RFD

Отзывы:

Похожие инструкции для Sensepoint XCD RFD

Бренды по названию

Популярные бренды