Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 61

Страница: 61 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

Log #4 (SRV2280-704 for TRUE-36; SRV2281-704 for TRUE-42)

: See Figure 7. Place Log #4 between the left and center

grate tines. Notches on log will rest on tines. Log should be positioned as far forward as possible. See Figure 8. Log #4

will lean against Log #2.

Log #3 (SRV2281-703)

: Locate log placement notches for Log #3. See Figure 5. Place Log #3 onto notches so that the

bottom of the log rests in the notch on log #2 and the top rests in the left hand side of the notch on Log #1. The top of the

burned area on Log #3 will be close to Log #1 when properly positioned. See Figure 6.

Figure 7.

RIGHT

RIGHT
HAND

HAND
NOTCH

NOTCH

FLAT AREA

FLAT AREA
FOR LOG #5

FOR LOG #5

Figure 8.

Figure 10. Log #5 - TRUE-42

Figure 6.

LOG RESTING IN NOTCH

TOP OF BURNED

TOP OF BURNED
AREA NEAR LOG #1

AREA NEAR LOG #1

LEFT

LEFT
HAND

HAND
NOTCH

NOTCH

LOG CONTACTS

LOG CONTACTS
LEFT GRATE TINE

LEFT GRATE TINE

LOG CONTACTS

CENTER GRATE

TINE

NOTCH

REAR GRATE TINE

FRONT GRATE TINE

LOG #5 APPEARANCE

LOG #5 APPEARANCE
VARIES SLIGHTLY

VARIES SLIGHTLY
BETWEEN MODELS

BETWEEN MODELS

Log #5 (SRV2280-705 FOR TRUE-36, SRV2281-705 FOR
TRUE-42)

: Locate flat area on Log #4 that will be used to

position Log #5. See Figure 8. Place Log #5 into appliance

as shown in Figure 9 or Figure 10. Left end of log should

rest against left side refractory just in front of air inlet on rear,

lower left of appliance.

Log #5 (TRUE-36):

Log #5 will sit about halfway between

front and rear grate tines, partially over pilot assembly. Log

#5 will contact log positioning tab as shown in Figure 9. Right

side of Log #5 will rest in notch on Log #4. See Figure 9.

Log #5 (TRUE-42):

Log #5 will rest against the rear grate

tine as shown in Figure 10. Right side of Log #5 will rest in

notch on Log #4. See Figure 10.

Figure 9. Log #5 - TRUE-36.

LOG CONTACTS LEFT

LOG CONTACTS LEFT
SIDE REFRACTORY

SIDE REFRACTORY

LOG POSITIONING

LOG POSITIONING
TAB FOR LOG #5

TAB FOR LOG #5

LOG CONTACTS LOG

LOG CONTACTS LOG
POSITIONING TAB

POSITIONING TAB

LOG #4 CONTACTS

LOG #2

LOG CONTACTS LEFT

LOG CONTACTS LEFT
SIDE REFRACTORY

SIDE REFRACTORY

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды