Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 34

Страница: 34 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

A. Vent Collar Preparation

Appliance Preparation

SEAL CAP

GASKET

Figure 6.2 Seal Cap and Gasket Location

CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.

NOTICE: This appliance is top vented ONLY.

1. Remove shrink wrap from appliance. Figure 6.1 shows

the shipping location of the seal cap and heat shields

(Section 6), splatter guard and finishing templates

(Section 10), and the logs and Teco-Sil (Section 11).

For TRUE-36G-IFT and TRUE-42G-IFT models, the

glass refractory is also shipped with the appliance. See

Figure 6.1.

Figure 6.1 Shipping Location of Components

SEAL CAP

LOGS

SPLATTER GUARD

FINISHING

FINISHING
TEMPLATES

TEMPLATES

HEADER HEAT SHIELDS

HEADER HEAT SHIELDS
(SHIPPED ON REAR SIDE OF APPLIANCE

(SHIPPED ON REAR SIDE OF APPLIANCE

TECO-SIL

GLASS REFRACTORY

GLASS REFRACTORY
TRUE-36G-IFT AND

TRUE-36G-IFT AND
TRUE-42G-IFT ONLY

TRUE-42G-IFT ONLY

HEADER HEAT SHIELD

AND FINISH TRIM

TRUE-36G-IFT AND

TRUE-42G-IFT ONLY

2. Remove seal cap from top of appliance by removing

one screw, which is included, to prevent construction

material from getting into appliance. Remove seal cap

when pipe installation phase begins. See Figure 6.2.

3. Ensure gasket seal is in place prior to installing vent

pipe sections. Gasket is installed at the factory.

NOTE:

Header heat shields and finish trim on TRUE-G

models are attached to appliance on the rear corner and

must be removed using a 1/4 inch nut driver. See Figure

6.3.

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды