Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 39

Страница: 39 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

D. Vertical Termination Requirements

Install Metal Roof Flashing

• See minimum vent heights for various pitched roofs

(Figure 7.9) to determine the length of pipe to extend

through the roof.

• Slide the roof flashing over the pipe sections extending

through the roof as shown in Figure 7.10.

Roof Pitch H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12 ............................1.25*

Over 7/12 to 8/12 ..............................1.5*

Over 8/12 to 9/12 ..............................2.0*

Over 9/12 to 10/12 ............................2.5*

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12 ........................... 5.0

Over 14/12 to 16/12 ........................... 6.0

Over 16/12 to 18/12 ........................... 7.0

Over 18/12 to 20/12 ........................... 7.5

Over 20/12 to 21/12 ........................... 8.0

Figure 7.9 Minimum Height From Roof To Lowest Discharge

Opening

HORIZONTAL

OVERHANG

VERTICAL

WALL

GAS DIRECT VENT
TERMINATION CAP

ROOF PITCH

IS X/ 12

LOWEST

DISCHARGE

OPENING

2 FT.

MIN.

20 INCHES MIN.

H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING

NOTICE:

Failure to properly caulk the roof flashing and

pipe seams could permit entry of water.

• Caulk the gap between the roof flashing and the outside

diameter of the pipe.

• Caulk the perimeter of the flashing where it contacts the

roof surface. See Figure 7.10.

• Caulk the overlap seam of any exposed pipe sections

that are located above the roof line.

CAULK

Figure 7.10

Figure 7.11 Insert Bolt into Brackets

Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.

• Slide the storm collar onto the exposed pipe section

and align brackets.

• Insert a bolt (provided) through the brackets and install

nut. Do not completely tighten.

• Slide the assembled storm collar down the pipe section

until it rests on the roof flashing. See Figure 7.11.

• Tighten nut and make sure the collar is tight against the

pipe section.

• Caulk around the top of the storm collar. See Figure 7.12.

* H minimum may vary depending on regional snowfall.

Refer to local codes.

Note:

When installing a silicone or EPDM pipe flashing boot

on a metal roof, it is recommended to put a bead of 100%

silicone sealant where the boot contacts the vent pipe to

prevent the entry of water. Follow the manufacturer’s recom

mendations when installing the boot. Climate regions with

frequent temperatures below - 50 °F (-45.6 °C) should use a

silicone flashing boot.

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды