manualshive.com logo in svg

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

"Тепло и истинный комфорт с отличным продуктом Heat&Glo TRUE-36-IFT. Установка и настройка прибора легки и удобны с инструкцией в руководстве. Скачайте руководство бесплатно на manualshive.com и наслаждайтесь новым качественным обогревателем уже сегодня!"

Поделиться
Скачать
background image

3

Heat & Glo  •  TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual  •  2461-980 Rev. Q  •  11/20

Installation Standard Work Checklist

Customer:          
Lot/Address:

Model  (circle  one):      TRUE-36-IFT   

TRUE-50-IFT 

                

 

 

         TRUE-42-IFT 

Date Installed:          
Location of Fireplace:
Installer:
Dealer/Distributor Phone # 
Serial #:

Comments Communicated to party responsible ____________________ by ______________________on ___________   
 

  

                                                  (Builder / Gen. Contractor/)   (Installer) 

                            (Date) 

 =  Contains updated information.

Hearth & Home Technologies recommends the following:

•  Photographing the installation and copying this checklist for your 

 le.  

•  That this checklist remain visible at all times on the appliance until the installation is complete. 

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in 
this installation manual.

WARNING! Risk of Fire or Explosion! 

Failure to install appliance according to these instructions could lead to 

a 

 re or explosion.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Appliance Install Information   

                     YES     IF NO, WHY?

Veri

 ed clearances to combustibles requirements are maintained. (Pg. 13-16)                              ___________________                         

Veri

 ed that the chase is insulated and sealed. (Pg. 17) 

 

              ___________________

Veri

 ed mantel and wall clearance requirements are maintained. (Pg. 49-50)                                ___________________

Veri

 ed hearth extension requirements are maintained. (Pg. 18)                                                    ___________________

Veri

 ed appliance is leveled and secured. (Pg. 35)                                                                         ___________________

Veri

 ed required factory-supplied non-combustible board installed. (Pg. 36)                                            ___________________

Venting/Chimney  Section 7 (Pg. 37-40)

Veri

 ed venting con

 guration complies to vent diagrams. 

 

              ___________________

Veri

 ed venting installed, locked and sealed/secured in place.  

                                  ___________________

Veri

 ed venting meets clearance to combustible requirements.                                                      ___________________

Veri

 ed wall/ceiling 

 restops are installed (if applicable). 

 

              ___________________

Veri

 ed attic insulation shield is installed (if applicable).  

 

              ___________________

Veri

 ed Exterior wall/Roof 

 ashing is installed and sealed. 

 

              ___________________

Veri

 ed termination cap is installed and sealed. 

 

              ___________________

Electrical  Section 8 (Pg. 41-43) 

Veri

 ed unswitched power (110-120 VAC) provided to the appliance. 

 

              ____

_______________

Veri

 ed wall switch wires are properly installed (if applicable). 

 

              ___________________

Gas  Section 9 (Pg. 44-45)

Veri

 ed appliance is using proper fuel type.  

 

              ___________________

If converted, veri

 ed proper fuel conversion kit was used. 

 

              ___________________

Veri

 ed that gas components (

 ttings, pressure taps, etc) are leak free and 

 replace is                                                                               

operating under correct pressures.                                                                                                          ___________________            

Finishing  Section 10 (Pg. 46-51)

Veri

 ed that 

 nish material does not interfere with install/operation of decorative front.                 ___________________

Veri

 ed combustible materials are not

 

installed in non-combustible areas.   

              ___________________

Veri

 ed all clearances meet installation manual requirements. 

 

              ___________________

Veri

 ed mantels/wall projections comply with installation manual requirements.  

              ___________________

Appliance Setup  Section 11 (Pg. 52-66)

Veri

 ed all packaging and protective materials are removed (inside & outside of appliance).                ___________________

Veri

 ed refractory (

 ber or glass) is installed properly.                                                                    ___________________

Veri

 ed Teco-Sil installed and properly fogged with black high temperature paint.                         ___________________

Veri

 ed Lava Rock, Mystic Embers, Glowing Embers, and logs installed correctly.                        ___________________

Veri

 ed 

 xed glass assembly installed and secured.                                                                       ___________________

Veri

 ed that a required decorative door option is installed properly.                                                ___________________

Veri

 ed remote control has been programmed and is fully functional.                                             ___________________

Veri

 ed proper air shutter setting for installation type and vent con

 guration.                                 ___________________

Manual bag and all of its contents are removed from inside/under 
     the appliance and given to party responsible for use and operation.                                          ___________________ 
   

                                                                                   

2461-982  12/16

Comments:

 Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective 

action needed ____________________________________________________________________________________

Содержание TRUE-36-IFT











































































Отзывы:

Нет отзывов

Похожие инструкции для TRUE-36-IFT

Martin BV4536 Installation And Operating Instructions Manual preview
BV4536
Бренд: Martin Страницы: 36
Napoleon GD 1800-NM Installation And Operation Instructions Manual preview
GD 1800-NM
Бренд: Napoleon Страницы: 14
Jensen La Valle RF-1591LP Owner'S Manual preview
La Valle RF-1591LP
Бренд: Jensen Страницы: 51
Majestic RUBY30IN Installation Instructions preview
RUBY30IN
Бренд: Majestic Страницы: 3
Napoleon GVFS60-N Installation And Operating Instructions Manual preview
GVFS60-N
Бренд: Napoleon Страницы: 20
FBR GAS X4CE-LX Manual preview
GAS X4CE-LX
Бренд: FBR Страницы: 30
Desa Wall Mantel with Base and Trim WD26CP Assembly And Installation Instructions Manual preview
Wall Mantel with Base and Trim WD26CP
Бренд: Desa Страницы: 8
Bio-Blaze DIAMOND I Safety And Assembly Instructions Manual preview
DIAMOND I
Бренд: Bio-Blaze Страницы: 16
Horizon Fireplaces Edge HCLC/P/L1100 Installation Instructions Manual preview
Edge HCLC/P/L1100
Бренд: Horizon Fireplaces Страницы: 22
Endless Summer GAD1001B Owner'S Manual preview
GAD1001B
Бренд: Endless Summer Страницы: 20
Travis Industries 430 Ember-Glo GSR2 Owner'S Manual preview
430 Ember-Glo GSR2
Бренд: Travis Industries Страницы: 74
Vola 860HE Installation And User Instructions Manual preview
860HE
Бренд: Vola Страницы: 36
Rinnai Royale ETR Freestanding Accessory Installation Manual preview
Royale ETR Freestanding
Бренд: Rinnai Страницы: 16
Touchstone 80006 Forte User Manual preview
80006 Forte
Бренд: Touchstone Страницы: 10
Napoleon PSL36SS Installation Instructions preview
PSL36SS
Бренд: Napoleon Страницы: 2
Majestic fireplaces Cabinets Classic Series Brochure & Specs preview
Cabinets Classic Series
Бренд: Majestic fireplaces Страницы: 4
IHP SV4.5HTKCT Installation Instructions preview
SV4.5HTKCT
Бренд: IHP Страницы: 4
IHP PCBE-42 Quick Start Manual preview
PCBE-42
Бренд: IHP Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды