Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 66

Страница: 66 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

J. Install Decorative Front

WARNING! Risk of Fire! Install ONLY decorative fronts
approved by Hearth & Home Technologies. Unapproved

decorative fronts may cause fireplace to overheat.

This fireplace has been supplied with an integral

barrier to prevent direct contact with the fixed glass

panel. DO NOT operate the fireplace with the barrier

removed.

Contact your dealer or Hearth & Home Technologies if

the barrier is not present or help is needed to properly

install one.
For more information refer to the instructions supplied with

your decorative front.

I. IntelliFire Touch

Control System Setup

• Detailed instructions for electrical wiring and connec-

tions are provided in Section 8.

• Verify that the 3-Position switch on the IFT-ECM is

switched to the REMOTE position. Detailed Operating

Instructions for the IFT-ECM are provided in Section

3.J of the Owner’s Manual.

Figure 11.24 IFT-ECM

This appliance is factory-equipped with an

IntelliFire

Touch

remote control. The remote was paired to the fire

place and tested at the factory. It does not need to be

paired again, unless an accessory kit will be added at

the time of installation. If no additional accessory will be

added, simply follow steps one through seven below.
1. If installed, remove batteries from remote.
2. Verify that the new appliance has power and secure

electrical connections.

3. Adjust the ECM selector switch to ‘REMOTE’ mode.
4. Wait to verify LED indicator on the ECM stops flash

ing.

5. Install batteries in the RC400 remote.
6. The RC400 remote will automatically pair to the appli

ance as pre-set at the factory.

3 POSITION SWITCH

TOP VIEW

LED INDICATOR

Log #8 (SRV2281-708):

Place Log #8 into appliance as

shown in Figure 14. Left notch will contact left grate tine and

base of log will rest on bottom refractory.

Figure 14.

LOG CONTACTS

LOG CONTACTS
GRATE TINE

GRATE TINE

Figure 15. Log Set Installed (Log #9 not visible in this view).

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды