Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 74

background image

35

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

Figure 6.4 Side Nailing Tab in Shipping Position

Figure 6.5 Nailing Tab Bent Out for Installation

Nailing tabs are provided on the appliance and on the heat

shields to secure the appliance to the framing members.

See Figure 6.4 and Figure 6.6 for location of nailing tabs

in shipping position.
•  Bend out side nailing tabs 90 degrees.  See Figure 6.5.
•  Place the appliance into position.
•  Keep side nailing tabs flush with the framing.
•  Level the appliance from side to side and front to back.
•  Shim the appliance as necessary. It is acceptable to use

wood shims underneath the appliance.

• Position and install heat shields by securing two screws

in each heat shield. See Figure 6.1 for shipping location

of heat shields. The heat shield screws can be found

pre-installed on the top of the appliance.

B. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

•  Sagging or loose insulation
•  Insulation backing or plastic
•  Framing and other combustible materials

Block openings into the chase to prevent entry of blown-
in insulation. Make sure insulation and other materials
are secured.

DO NOT notch the framing around the appliance

standoffs.

Failure to maintain air space clearance could cause

overheating and fire.

Figure 6.3. Shipping Location of Header Heat Shields and Finish

Trim Pieces - TRUE-36G-IFT and TRUE-42G-IFT

• Bend the top header heat shields upward to position

them vertically and bend out the two nailing tabs on the

top of each header heat shield. Secure to framing. See

Figure 6.6.

• Secure the appliance to the framing by using nails or

screws through the nailing tabs.

• Optional: Secure the appliance to the floor by inserting

two screws through the pilot holes at the bottom of the

appliance.

Figure 6.6. Heat Shields and Nailing Tabs in Installation Position

HEAT SHIELD NAILING

TAB IN SHIPPING

POSITION

HEADER HEAT SHIELDS

HEADER HEAT SHIELDS

FINISH TRIM PIECES

FINISH TRIM PIECES

REMOVE SCREW

REMOVE SCREW

«
...
33
34
35
36
37
...
»

Содержание TRUE-36-IFT











































































Отзывы:

Нет отзывов

Похожие инструкции для TRUE-36-IFT

Бренд: Nectre Fireplaces Страницы: 13

Бренд: Home Decorators Collection Страницы: 16

Бренд: Pacific energy Страницы: 24

Бренд: HAMPTON BAY Страницы: 48

e-MatriX 800-500 ST LL

Бренд: Faber Страницы: 24

Бренд: Mendota Страницы: 45

Бренд: Looft Industries Страницы: 16

Бренд: Valor Страницы: 46

Бренд: Superior Fireplaces Страницы: 30

Бренд: Room&Board Страницы: 30

Бренд: FMI Страницы: 40

Бренд: Obadiah Страницы: 5

Бренд: Napoleon Страницы: 124

Бренд: Canvas Страницы: 100

Бренд: HAMPTON BAY Страницы: 48

Бренд: FireplaceXtrordinair Страницы: 10

Бренд: Nibart Страницы: 44

MAJESTIC ODGSR36ANAU

Бренд: Raypak Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды