Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 18

Страница: 18 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

NON-COMBUSTIBLE
BOARD

HEARTH CLEARANCE
BRACKET

NON-COMBUSTIBLE
HEARTH EXTENSION
1 IN. THICK MAX.

WOOD OR OTHER COMBUSTIBLE

FLOOR OR PLATFORM

D. Hearth Extension

WARNING! Risk of Fire! Non-combustible hearth exten-
sion may be required when appliance is installed on com-
bustible surface.

• Hearth extension must be non-combustible and

serves to protect combustible floors in front of appli

ance. See Figure 3.10 and Figure 3.11.

• T

he base of the fireplace may sit on a combustible

surface. See Figure 3.11.

The area in front of the

appliance must be protected by a non-combustible

hearth extension, unless the appliance is raised a

minimum of three inches above the combustible floor

or hearth. See Figure 3.11 and Figure 3.12.

•

If a hearth greater than one inch in thickness is de

sired, the appliance must be raised by the equivalent

height to ensure that the hearth extension does not

interfere with the installation of the glass assembly

required for fireplace operation. See Figure 3.11.

Figure 3.10 Non-Combustible Hearth Extension Dimensions

NON-COMBUSTIBLE

MODEL

in.

TRUE-36-IFT

305

57-1/4

1454

TRUE-42-IFT

305

63-5/16

1608

TRUE-50-IFT

305

71-5/16

1811

Figure 3.11 Appliance Installed on Combustible Surface

Non-Combustible Hearth Extension REQUIRED.

NOTICE: DO NOT install a hearth that is greater than
one inch thick. Hearth will interfere with installation of
glass assembly. Total hearth height must not exceed one
inch from bottom of appliance when appliance is installed

directly on floor (including mortar, backer material, etc.).

NON-COMBUSTIBLE
BOARD

HEARTH CLEARANCE
BRACKET

WOOD OR OTHER COMBUSTIBLE

FLOOR OR PLATFORM

4 IN.

3 IN. MIN.

BOTTOM OF
FIREPLACE

1/2 IN. MAX.
THICKNESS
COMBUSTIBLE
BUILDING
MATERIAL

Figure 3.12 Appliance Raised a Minimum of 3 Inches Above
Combustible Surface. Non-Combustible Hearth Ex-

tension NOT REQUIRED.

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды