Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 64

Страница: 64 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

Log #5 (SRV2281-705)

: Locate flat area on Log #4 that will be used to position Log #5. See Figure 8. Place Log #5 into

appliance as shown in Figure 9. The left side of the log will rest on bottom refractory and pilot bracket. It will also lean against

rear grate tine. The right side of Log #5 will rest in notch on Log #4. There will be a space approximately 1-3/4 inches from

the end of the log to the left side refractory.

Log #4 (SRV2282-704)

: See Figure 7. Place Log #4 between the left and center grate tines. The base of Log #4 should rest

on the refractory. Notch on log will rest on the front left grate tine and the top of log will rest in notch on Log #2. See Figure 8.

Log #3 (SRV2282-703)

: Locate log placement areas for Log #3. See Figure 5. Place Log #3 into notch on Log #1 so

that the base rests on the flat area of log #2. The top of the burned area on Log #3 will be close to Log #1 when properly

positioned. See Figure 6.

Figure 7.

NOTCH

NOTCH FOR LOG #5

Figure 8.

Figure 9.

Figure 6.

LOG RESTING IN NOTCH

TOP OF BURNED

TOP OF BURNED
AREA NEAR LOG #1

AREA NEAR LOG #1

LOG NOTCH

LOG NOTCH
CONTACTS

CONTACTS
LEFT GRATE TINE

LEFT GRATE TINE

LOG RESTS ON REFRACTORY

LOG RESTS ON LOG #2

LOG RESTS ON LOG #4

LOG RESTS ON BOTTOM REFRACTORY

LOG RESTS ON PILOT

LOG RESTS ON PILOT
BRACKET AND LEANS

BRACKET AND LEANS
AGAINST REAR GRATE

AGAINST REAR GRATE
TINE

TINE

1-3/4 IN.

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды