Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 74

background image

19

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

A. Vent Termination Minimum Clearances

Roof Pitch

H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5*

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

Figure 4.1 Minimum Height From Roof To Lowest Discharge
Opening

HORIZONTAL

OVERHANG

VERTICAL

WALL

GAS DIRECT VENT
TERMINATION CAP

12

X

ROOF PITCH

IS X/ 12

LOWEST

DISCHARGE

OPENING

2 FT.

MIN.

20 INCHES MIN.

H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING

4

4

Termination Location and Vent Information

Fire Risk.

Maintain vent clearance to combustibles as

specified.

•

DO NOT

pack air space with insulation or other

materials.

Failure to keep insulation or other materials away

from vent pipe may cause overheating and fire.

WARNING

Figure 4.2 Staggered Termination Caps

Gas, Wood or Fuel Oil

Termination Cap

B

Gas

Termination

Cap **

A *

*

If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.

**

A

B

6 in. (minimum) up to 20 in.

152 mm/508 mm

18 in. minimum

457 mm

20 in. and over

0 in. minimum

In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.

NOTICE: TRUE-50 Models Only

Horizontal vent terminations are NOT approved for

installation with vinyl siding or vinyl soffits. Permanent

damage to vinyl siding or vinyl soffits may occur.

NOTICE: TRUE-36 and TRUE-42 Only:

Horizontal vent terminations ARE approved for installation

with vinyl siding and/or vinyl soffits provided the VPK-DV

(vinyl protector kit) is installed. Permanent damage to vinyl

siding or vinyl soffits may occur.

* H minimum may vary depending on regional snowfall.

Refer to local codes.

«
...
17
18
19
20
21
...
»

Содержание TRUE-36-IFT











































































Отзывы:

Нет отзывов

Похожие инструкции для TRUE-36-IFT

Бренд: Valor Fires Страницы: 49

Бренд: Majestic fireplaces Страницы: 56

Бренд: Valor Страницы: 5

Бренд: Glow Fire Страницы: 73

Бренд: Superior Fireplaces Страницы: 20

Бренд: Valcourt Страницы: 70

83035033 WW11994

Бренд: UBERHAUS DESIGN Страницы: 11

Бренд: Jensen Страницы: 48

WALDON CTCFP60-5

Бренд: Canvas Страницы: 100

Бренд: bio chimenea Страницы: 4

Бренд: Backyard Creations Страницы: 6

Бренд: Amantii Страницы: 33

Бренд: Coleman Страницы: 8

KIT Glamm 3D Plus 1000

Бренд: GlammFire Страницы: 24

Бренд: Extraflame Страницы: 44

Бренд: DEKO LIVING Страницы: 9

Бренд: Nibe Страницы: 20

Бренд: Desa Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды