Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 74

background image

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

6

2

2

Getting Started

A. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to

operate with all combustion air siphoned from outside of

the building and all exhaust gases expelled to the outside.

No additional outside air source is required.

Installation MUST comply with local, regional, state and

national codes and regulations. Consult insurance carrier,

local building inspector, fire officials or authorities having

jurisdiction over restrictions, installation inspection and

permits.

Before

installing, determine the following:

•  Where the appliance is to be installed.
•  The vent system configuration to be used.
•  Gas supply piping requirements.
•  Electrical wiring requirements.
•  Framing and finishing details.

• Whether optional accessories—devices such as a wall

switch or remote control—are desired.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following

tools and building supplies are available.
Tape measure

Framing material

Pliers Hammer
Phillips screwdriver Manometer

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Flat blade screwdriver
Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300 ºF minimum continuous exposure

rating)

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualified

service technician, service agency or your dealer.

B. Good Faith Wall Surface

NOTICE: Temperatures listed above are taken with a
temperature measuring probe as prescribed by the test

standard used for appliance certification. Temperatures

on walls or mantels taken with an infrared thermometer
may yield increased temperatures of up to 30 degrees or
more depending on the thermometer settings and material
characteristics being measured.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

22 IN.

34 IN.

40 IN.

46 IN.

52 IN. MIN.

CEILING

28 IN.

APPLIANCE FRONT

FIREPLACE OPENING

165°F+

150°F

160°F

155°F

160°F

16 IN.

180°F+

10 IN.

230°F+

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

Figure 2.1 Good Faith Wall Surface Temperatures Above Appliance

«
...
4
5
6
7
8
...
»

Содержание TRUE-36-IFT











































































Отзывы:

Нет отзывов

Похожие инструкции для TRUE-36-IFT

Бренд: Valor Fires Страницы: 64

Бренд: Jetmaster Страницы: 13

Бренд: Valor Страницы: 14

Бренд: ZANTIA Страницы: 88

La Valle RF-1591LP

Бренд: Jensen Страницы: 51

Бренд: Majestic Страницы: 3

Бренд: Valor Страницы: 38

Бренд: Dimplex Страницы: 2

Бренд: Fire Sense Страницы: 7

(V)KC42NE SERIE

Бренд: Desa Страницы: 40

Бренд: Dimplex Страницы: 15

Бренд: Desa Страницы: 36

Бренд: Heat & Glo Страницы: 46

MERCURY MERC32IL

Бренд: Majestic Страницы: 67

RUTHERFORD 50-B

Бренд: Heat&Glo Страницы: 48

Бренд: Heat&Glo Страницы: 56

Бренд: Outdoor Plus Страницы: 14

Nightfire Tripod CFT-POD-K

Бренд: Outdoor GreatRoom Company Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды