Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 56

Страница: 56 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

7. Place back glass panel with arched portion down into

the rear of the appliance. See Figure 11.13. Slide the

white side spacers toward the rear of the appliance

until they contact the rear glass panel.

Figure 11.12 Left Refractory Tab

Figure 11.13 Installed Black Glass Rear Panel

8. Slide left glass panel into the appliance until it con

tacts the rear glass panel. Ensure the notch is on the

bottom side. Bend the refractory tabs over to retain

the glass. See Figure 11.14.

9. Slide right glass panel into appliance until it contacts

the rear glass panel. Bend the refractory tabs over to

retain the right glass panel. See Figure 11.15.

10. Place tabs of the finish trim behind the white side

spacer and refractory tab. Push the finish trim into

place until it is flush with the outside of the firebox.

See Figures 11.16 and 11.17. Repeat for opposite

side.

Figure 11.14 Left Refractory Tab

Figure 11.15 Right Refractory Tab

Figure 11.16 Upper Right Finish Trim

BEND TABS

BEND TABS TO RETAIN GLASS

LEFT SIDE SPACER

LEFT

LEFT
SIDE

SIDE
SPACER

SPACER

RIGHT

SIDE

SPACER

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды